Simon

Administrators
  • Content count

    4,109
  • Joined

  • Last visited


About Simon

  • Rank
    Technical Support
  • Birthday 01/28/1978

Contact Methods

  • Website URL http://www.linkecu.com
  • Skype link-technical-help

Profile Information

  • Gender Male
  • Location Christchurch, NZ
  • Interests All things with wheels.
    But mostly RC cars

Simon's Activity

  1. Simon added a post in a topic G4 Storm install - Aux outputs grounded before ECU first powered up   

    Yes there will be a path to ground through the components when the ecu is powered down
    In the pc link help file there is a good explanation of this
    Navigation:  G4+ ECU Tuning Functions > Auxiliary Outputs >
    Wiring Auxiliary Outputs
     
  2. Simon added a post in a topic Mitsubishi colt ralliart 4g15t mivec trigger pattern   

    No nothing at this point unfortunately it is a busy time for us currently
  3. Simon added a post in a topic fuel pump wiring & cooling fan wiring (SR20DET)   

    ECU will switch ground to control both and they will require relays as the ECU can only switch 2Amps max.
    Fuel Pump is on pin 18 in a factory set up.
    Fan is on pin 19
     

  4. Simon added a post in a topic Mini R53 Base File   

    File is from the base maps folder in PC link
     
    BMW Mini R53 G4+ Xtreme Plugin.pclr
  5. Simon added a post in a topic S54 Base Map   

    Thank you for shearing integraleV8
  6. Simon added a post in a topic Skyline can't connect   

    Are you able to open base maps ok with out the error?
    You will see a code like this in PC link sometimes if the ECU is on very old firmware or an older generation G4 not G4+
     
  7. Simon added a post in a topic Bmw Cam Sensor   

    Most Hall sensors will take a 12V supply pinout wise it will be a case of working it out from factory diagrams for the sensor.
     
  8. Simon added a post in a topic Mini 1275 with Single Point Injection   

    Yep that can be done you will likely need a 4R7 ballast resistor giving a opening current of 2.2amps
    If the injector requires a high current then the next step is to go to a 2R2 ballast giving 3.8amps
     
    Regards
     
    Simon 
  9. Simon added a post in a topic link g4 monsoon boost   

    One side of solenoid to a switch 12V and the other to the ECU Aux out.
  10. Simon added a post in a topic Cam level trigger edge   

    You would need to disconnect the spare ignition channels as they will try to fire when you do the test. They will need to be reset to the Aux functions once done too.
  11. Simon added a post in a topic Cam level trigger edge   

    A test to confirm your injector timing will be to set the ignition mode to direct spark and see if timing is correct on cylinder 1 while cranking then turn back to wasted.
  12. Simon added a post in a topic Cam level trigger edge   

    That is correct.
    Are you running wasted spark or distributor?
  13. Simon added a post in a topic Innovate MTX-L Plus wiring into spare AN Volt channel   

    Hi John
    What you will have is the later 06-07 ECU which has a different pinout to the 04-06
    You will find AN Volt 7 s on pin B4 (factory O2 signal)
     
  14. Simon added a post in a topic Cam level trigger edge   

    HI Jay
     
    It wont matter as if you are running cam level it purely looks to see if signal is high or low, the Edge is not used in this case.
    But the signal must be High as the gap passes for the next turn of the crank.
  15. Simon added a post in a topic TT Plugin Boost Switch   

    It is an additional connector on the PCB that you can connect to with an XS Loom,
    Note image is from assembly instructions and connector is not fitted but circle shows location.