Jump to content

Brad Burnett

Dealer
  • Posts

    792
  • Joined

  • Last visited

  • Days Won

    38

Brad Burnett last won the day on March 2 2022

Brad Burnett had the most liked content!

6 Followers

Profile Information

  • Gender
    Female

Recent Profile Visitors

4,802 profile views

Brad Burnett's Achievements

  1. Adam, I spoke with the owner of the car yesterday and discussed eliminating the ignitor and going with readily available 350z coils.
  2. Yes sir. I know Paul from back when he lived in texas many moons ago. I spoke with him on the phone a hour or so ago. The aem disc wont fix an optical issue at all. Let me review the cal and log and ill get back with yall.
  3. How much boost and what is the plug gap? And an aem trigger wheel will not fix the problem if the issue is the optical pickup. Ive been down that road a few too many times.
  4. The only things in the cluster that is CAN based is the coolant temp and some of the small indicator lamps. You should be fine with most everything else. I have done both the altezza plug in and link wire in unit on multiple IS300s with factory cluster.
  5. ITB balance issues are the most common issues i see with starting and idling issues, Most people never touch them. I also run an ITB 1st gen 1uz. Buy a couple sets of these: https://www.amazon.com/Niome-Motorcycle-Carburetor-Synchronizer-Cylinder/dp/B083K6MX1F/ref=sr_1_1_sspa?crid=OMFJFITVMLSF&keywords=synchrometer&qid=1670940483&sprefix=synchrometer%2Caps%2C157&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExNlJEQTNZTENET1AwJmVuY3J5cHRlZElkPUEwMjI5MzkwM0tPVVMwTjdaRUxDTCZlbmNyeXB0ZWRBZElkPUEwMDI4NjM0MlJWWjM0M1VCQTNQUiZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU= Just make sure that all the balance tubes are disconnected so the throttles arent pulling from other cylinders.
  6. Are you running ITBs? If not there is no reason to have load set to TPS in most cases.
  7. Sounds like the pinout at the tps connector is wrong. If you look in the Analogue Voltages tab in the runtime value list(F12 or r), do you have any voltage on the ANVolt channel the tps is connected to?
  8. Wiring is correct as described, just make sure that the 12v source on 85 is switched with key. Set up general purpose out put as IGn8 and switch conditions to Map > X. I would add conditions to secondary fuel pump to include if the primary pump is on, differential fuel pressure < Y, Inj duty>Z, etc. You can get creative with adding different logic to trigger the second pump.
  9. does it lose the signal or is it just going lean off the selected scale due to over run fuel cut? Maybe configure the autotune to disregard any value that is occurring on overrun?
  10. In the inlet manifold tends to lend to heat soak. Typically better readings pre throttle body. Id tend to pick the AEM style sensor.
  11. Change the load axis on the WG duty table to target boost and not MAP
  12. Brad Burnett

    Boost Nightmare!

    Is the fire ring/valve seat for the WG valve in place between the WG and the manifold? That is the main reason I can come up with for had boost now you dont. And adding springs will not fix a creep issue. That is an issue caused by too small of a gate or poor wastegate priority. Id bet on priority as you have a 66mm gate.
  13. Ive come into this issue many times. But I rarely have the ecu calibrate the TP main/sub values. Just manually work the throttle blade with the power connection disconnected and record the min/mx values for TP main/sub.
  14. I would recommend a retune. You will 100% need to resync the ignition. I have gotten by with a simple copy and paste all the pertinent data.
  15. Brad Burnett

    2nd knock sensor

    I may be incorrect, but from the last convo I had with Adam regarding this exact scenerio(2jz w/ altezza pnp), I recall him telling me to just wire both sensors to the same input pin and just adjust your gains as necessary.
×
×
  • Create New...