Jump to content

Adde

Members
  • Posts

    21
  • Joined

  • Last visited

Everything posted by Adde

  1. I install new gearbox grom STI GRB to my STI04. New transmission dont have speed sensor. Can i use ABS wheel sensor as veh speed sensor. I need connect ABS sensor to DI?
  2. I reconnect one part ecu of other, spray contacts with contact cleaner, and ecu works.
  3. in test function spikes cyl1 and cyl3 the same.
  4. We look on trigger wheels, all ok. And i write trigger scope. Trigger Scope Log 2019-07-20 7;22;12 pm.llg
  5. If ecu plug will have be damage we dont have any signal on osciloscope. But we have signal and have frequency of signal. I connect dirrectly to ecu and from cyl 1 2 4 we have good signal but from inj 3signal wrong. Tell me why?
  6. I cut wire and connect directly to ecu, this osciloscopes makes from ecu. Problem is in ECU not in wiring, but Link repair service dont find it.
  7. Its joke? Do you think i dont check 12v supp before send to your service ecu from Ukraine to NZ? I check, all OK, but inj3 still dont work.
  8. This osciloscope of 2 working cylinders and osc of one working and one bad working cylinder(cyl3). How do you test ecu, if it slill work bad?
  9. I recive ecu. You dont find any problems, but signal inj 3 still wrong and car dont work good. Can i log in link software inj timing of each cylinder?
  10. Please recive my ECU for repair. EMS number EE875015059UA. I write form on main site, but repair number i dont have. 26/06/2019 08:40 Delivered HWO
  11. In mu link G4+ WRX7-9 deffective INJ3 output signal(it work good, but now dont work), cyl 1 2 and 4 work good, but cyl 3 not working. Can i connect inj 3 signal to other ecu output and reconfig it?
  12. Yes it 5744 Hz. What Freq channel i should use(6 kHz Narrow band or 4-10 wide band)?
  13. I install knock sensor 0261231006. I calculate knock freq. My calculation is 5,7439. What Freq channel i should use?
  14. Maybe you have some manual how to tune my ecu with knock correction and control. I understand that wideband sensor is better. Bosch 0261231006 i install in two days. Please give me some manual.
  15. Adde

    ID2000

    What parameters i need write to ecu to proper install injectors ID2000. I write Flow data 43.5 1455 950 680 495 375 2225 Short Pulse Width Adder 0,000 0,125 0,250 0,375 0,500 0,625 0,750 0,875 1,000 1,125 1,250 1,375 1,500 1,625 1,750 1,875 2,000 2,125 2,250 2,375 2,500 2,625 2,750 2,875 3,000 3,125 3,250 3,375 3,500 3,625 3,750 3,875 4,000 0,2000 0,2284 0,2135 0,1866 0,1601 0,1339 0,1068 0,0808 0,0542 0,0264 0,0013 -0,0019 -0,0001 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000 0,0000
  16. Adde

    What trigger to use

    because synhro old variant is better then new on rpm more than 9000
  17. Adde

    What trigger to use

    I try to use trigger V1-6 but ECU dont see rpm. Inj plug and play data for 4 bar, but 4 so much for me I use 3 bar table from site ID. But in ECU I dont find static injector flow parameter. Dead time i write in ecu. So 2 questions: 1. Trigger 2. Static flow
  18. Adde

    What trigger to use

    I install 6 tooth crankwheel and 7 tooth camwheel to G4+ WRX ECU. What trigger settings i should use? And what parameters i need to write to install ID2000 injectors? cam and crank wheels in right side of picture.
×
×
  • Create New...