Jump to content

gtihk

Members
  • Posts

    53
  • Joined

  • Last visited

Everything posted by gtihk

  1. Look at Deatschwerks. They have a good range but according to experience, their deadtimes are not usually spot on.
  2. gtihk

    Link Force GDI

    I have an answer from Adam. For the benefit of others who may want to know. A1 can have flow of up to 10A and A5 is relatively low current of not more than 3A.
  3. gtihk

    Stalling Issue

    Try increasing Idle aim and also adjust normal position of the ISV. Different cams may require some more air to idle. Also look at ignition timing. May need more too.
  4. According to memory, a DI input can be configured as anti-theft. We also in the past fitted a hidden switch to interfere with trigger inputs, not necessarily to disconnect it.
  5. I think you mainly use Factory wiring with the single knock wire to the Bosch which other side should be wired to any sensor ground.
  6. gtihk

    Link Force GDI

    May I know the Maximum current draw on Pins A1 and A5 on the Link Force GDI ECU please?
  7. gtihk

    Closed loop lambda

    I have a question regarding closed loop fuel. In the log attached, at around 6000 rpm, Lambda aim is 0.88, Lambda 1 is 0.992, yet the ECU is pullinCIVIC RUN1.llgg 12% fuel. Why does it do that? Honda Civic 92-95 G4+ Xtreme Plugin V2.0.pclr
  8. gtihk

    Link Force GDI

    Anyone please confirm where CAN 1 is connected please? I can see CAN 2 on connector B. Could CAN 1 be on the Port below the USB tuning port?
  9. gtihk

    CAN Lambda

    I used the same sensor with a conventional Lambda controller. The sensor seems OK.
  10. gtihk

    CAN Lambda

    Sensor was brand new from the box. Not dropped once. Resister in place.
  11. gtihk

    G4+ Bluetooth

    Let me know if I can be of help when you have the hardware arrived.
  12. gtihk

    CAN Lambda

    I am trying to install CAN Lambda to a Civic EG with plugin ECU. I followed the instructions and added a dedicated relay with the correct gauge wire. I am seeing errors 16, 33 and 34. I even added a 35v 22 uF capacitor as suggested. Still no luck. Anyone?
  13. gtihk

    G4+ Bluetooth

    I had some problems initially but Michael at Virtualhere was very helpful. He used Teamviewer to help me. Considering that I did not pay for the software, it was wonderful service.
  14. I think you need to consider using a different tuner. There should be plenty around in Victoria?
  15. I WOULD START WITH ABOUT 16.
  16. gtihk

    G4+ Bluetooth

    Thanks, it is working now with firewall turned off. I did not personally turned it on, but I guess it is a default to be On.
  17. gtihk

    G4+ Bluetooth

    I have the Mini Router now and updated its firmware as advised. I can connect to the CloudhubXXXXXX, but cannot see ECU. Any ideas please?
  18. gtihk

    G4+ Bluetooth

    This is 12v in and 5v out. It does not sound right. The WiFi device should need 12v, right?
  19. gtihk

    G4+ Bluetooth

    Where can I get one please?
  20. gtihk

    G4+ Bluetooth

    What is a 12V micro USB adapter? Is it where the power for this WiFi Router is coming from? https://salaskoracing.com/collections/salasko-racing-motorsports-electronics/products/ethernet-wifi-adapter This looks nice but quite expensive.
  21. I do not know what ECU you are using. You can use the plug in base map as a start file but make sure that your inputs and outputs are matching. In particular, you need to look at MAP sensor allocation and calibration as the plug in uses an internal MAP sensor.
  22. you need to tell the ECU what sensor you have in order to have a correct temperature. As for the fan, I think you could test is by assigning it as a GP output and then use the test output function.
×
×
  • Create New...