Jump to content

drifter17a

Members
  • Posts

    14
  • Joined

  • Last visited

Everything posted by drifter17a

  1. does anyone know of formula to convert load based mg/stroke in ignition table which is based on maf to pressure based map ?
  2. Yeah I get that and the need to find a base, gain, tune tables and action(retard or fuel cut) to clarify I was stating if I turn the car on and rev slightly standing still while knock control is on, If i see a graph then it confirms the link ecu is plugged into the factory knock sensors which I believe the answer is yes from your earlier post:)
  3. So If i turn the car on and enable knock control, I should see the graph loggers if my sensors are working?
  4. Thanks mine is g4 + plug in.i am going to see if it works with factory sensors, I do think rb25 have knock sensors on the block just not sure if it is connected in link, would these be recognised as input such as analouge or digital or no it is seen as sensor if using the original wiring for plug in?
  5. Hi All, I have an r34 gtt and want to setup knock control as realised it was not setup by my tuner. Car is quite load with forge engine, how would I find the target and gain to set this up? When I look at the option to setup this, I can see three ways, use existing knock sensor as analouge input, I don't think link supports this , use link internal knock sensor or external. re internal knock sensor, how does this work ? is there a cable of some sort for link to recognise ping / knock ? re extrnal sensors, what are my options ?
  6. so I mapped the pins as per this link and my maxicom does not support it https://www.autelstore.co.uk/wholesale/autel-maxicom-mk808-diagnostic-tool.html?gclid=Cj0KCQiAqo3-BRDoARIsAE5vnaKsLh-sn8cKvzkdH1CrqG3mb3u-DT01nvn1Y5rBSiwnTwzv8FPTw-MaAvC_EALw_wcB it looks as I am out of any options, can't find any consult 1 or consult 2 reader. as i understand consult 3 or consult 3 plus won't support my car. about to pull my hair. https://www.chinatopcable.com/product/nissan-14-pin-to-obdii-16-pin-adapter-connector-cable-4-pin-pass-through-for-nissan-0-4-meters/ done for the night but was thinking of trying combination below tomorrow https://www.aliexpress.com/item/32672838945.html or buy this https://www.cardiagtool.co.uk/svci-ing-infiniti-nissan-diagnostic-tool.html?gclid=Cj0KCQiAqo3-BRDoARIsAE5vnaKIkRaLcxMIuGeknqHBl1XS_QzSPEgs4-kWQSrL8QI9_WZiq885suUaAlYrEALw_wcB
  7. just done this many time today and abs stays on constant. i drove 30 kmh and done it many times i have maxicom and it does have skyline but it is obd port I have bought the 14 pin obd1 to obd 2 to see if I can get it to scan.
  8. Many thanks do you have pic of other page showing how to erase the codes? where is this manual, anywhere I could download it?
  9. Hi all link ECU installed with no abs sensor wired into ecu. All was fine for a year and abs light came on recently I access link via original usb cable and consult is still there however can't read any ecu from consult hicas unplugged and had datascan software but hicas nor ecu can not br read obviously as they are non existent any idea what I should do? thanks
  10. Hi i can’t download the pdf as it says unavailable i am using an android with female to female adaptor on usb so i can connect the original usb cable from my galaxy to the unit i have selected serial connection out of the three option if wifi and blueetooth and serial any help with be appreciated
  11. Hi guys, couple of questions when you take ur car to tuner , what does it mean when they lock the map? does that mean you can’t see the values or you can but can’t change it? on link g4 plug in, can you have a switch for anti lag so it can be switched on and off? does link g4 support fuel pressure and oil pressure sensor so it can stop the engine reving above 3k if oil or fuel pressure is low? finally, is there a wireless solution so you can see pc link on iphone to use as monitoring gauge? What do i need to have an obd wired in?
  12. Many thanks that won’t impact the engine negatively or blow it up does it? i have read the manual and it seems it is plug and play and i don’t even need to run vacuum pipe to ecu as I can just use the r34 boost pressure sensor or map sensor without any rewiring
  13. drifter17a

    r34 g4 pug in

    all, i own an r34 gtt and I think standard injectors are 370cc or so and have purchased a 630cc injectors. i just need to start the car and let it run for little while before taking it to tuner so question is, can i change the fuel duty cycle or injector opening time to half so essentially the engine can run in idle and low speed with new injectors?
×
×
  • Create New...