[Using Factory Knock Sensor VR4Link/ DSM]

Hi Adamw, would you mind sending me how to turn in on for knock setting with stock knock sensor, now using the Evo1-3 g4+ plug in. 

Thanks. 

 

Hi Adamw, thanks for you reply. Because evo 1-3 plug in have stock knock sensor is connected to pin 58, I just wanna to know how to turn it on. 

Thanks. 

 

[Using Factory Knock Sensor VR4Link/ DSM]

Hi Adamw, would you mind sending me how to turn in on for knock setting with stock knock sensor, now using the Evo1-3 g4+ plug in. 

Thanks. 

[Evo 1-3 plug in COP]

Hi Adams, 

Thanks for your information. 

[Evo 1-3 plug in COP]

Hi, I have one of Evo 3 running Link Evo 1-3 g4+ plug in. 

Now I convert to COP with wasted spark mode and using Honda k20 coil. 

So I need change the dweel time? If need to change, can I know the dwell time setting. 

Thanks. 

[Trigger setup]

Who’s have read my log file, please tell me how to solve the idle misfiring problem.Thanks

[Trigger setup]

This is basemap by attached.

basemap 01.pclr

[Trigger setup]

Hi, I already on the narrowband o2 sensor and adjust some the fuel setting, result is better thank before. But just now having problem with idelling, there missfire on idle. Can help to check the problem.

idlle log file 01.llg idlle log file 01.llg

[Trigger setup]

Ok, thanks Adamw. I will on the lambda mode and test again. Will report.

[Trigger setup]

Ok, I have connected the lambda at analog out 4, but I still never on the lambda yet. do you know the lambda sensor calibration for this single pin type. But look like Honda Civic 92 lambda type. Thanks

[Trigger setup]

Hi, I start the engine today and trigger offset is set to 320 degrees and lock the ignition timing to 10 degrees BTDC by timing light. But I having the problem now, when I tested on the road, the rev rpm only up to 3500rpm only. Something like fuel cut. Can help to check the bace map and log file?Maybe is injector timing problem? Now I’m have install turbo charger and direct spark mode for this engine. Hope can help to solve the problem. Thanks.

 

[Trigger setup]

Ok, I  understood and I will try doing trigger calibration. Will report if having problem.

[Trigger setup]

Hi, I have complete the wiring,  any basemap to support for this model? Now I have installed direct spark. Thanks

[Trigger setup]

Hi, finally I received link monsoon, before start the wiring job, I need make sure the trigger wiring. It’s the red wire is connect to trigger 1 ? How about the trigger 2.? Thanks

[Trigger setup]

Ok, thanks for you suggested.

[Trigger setup]

Ok, thanks Adam, witch type of G4plus is recommended? Now the engine is installed turbo.

[Trigger setup]

Hi Simon, thanks for you reply. So I can start the engine with daihatsu copen mode without the crank sensor? 

[Trigger setup]

Hi Adam , the picture is attached.

[Trigger setup]

Ok, I will take later. Thanks Adam

[Trigger setup]

Thank for you reply. Yes, but no distrbutor type. The picture attached.

[Trigger setup]

Hi, may I know this Suzuki G13b engine can install link G4+ ? And can done the trigger setup for this type of engine? Because I need upgrade  direct coil on spark plug.

 

 

[Tacho not working]

Thanks for you reply, i will try in. 

[Tacho not working]

Thanks for you reply, so what you suggest for tacho output, witch Aux is better. The original tacho is connected to ECU. 

[Tacho not working]

Hi, i have one of suzuki jimny jdm and swap to suzuki M16A VVT engine with Linkecu G4 plus civic 92-95 connector. I have set my tacho out with Aux 6.

But why my original tacho meter still not working. It's the setting problem or wrong signal. Please tell me how to solve it.  Thanks.....