Jump to content

OSF2004

Members
  • Posts

    25
  • Joined

  • Last visited

Everything posted by OSF2004

  1. OSF2004

    Connection error

    Nevermind, i have found the problem.. the usb connector in laptop loose
  2. OSF2004

    Connection error

    Hi i have a little problem with ECU to laptop connection. its always disconnected ( connection error : 1047 Serial error ), when the engine on. But the connection great if the ecu stays in ignition on without the engine run. I tried to other laptop, the problem still remain. the engine run for a few minute and suddenly the connection error. any idea what the problem is ? Thanks William i also tried use my G4+ cable also but still the same
  3. Thank U soo Much sir. Best regards William
  4. Ok, i will use the waste spark. please help me with the wiring setup. I just need to wire ign 1 & Ign 2 Ign 1 i will pararel to ignition coil 1 & ignition coil 4 right ? And ign 2 pararel to ignition coil 2 & ignition coil 3 right ? Anything i have to setup at the link software? Thank U
  5. I just test the ign1, ign2, ign3, there is a spark. But ign4 no spark. I test it with ign test. The volt at ign 1,2,3 is 10.4mV The volt at ign 4 quite high 240mV. Is it because of the short circuit ? My other option is using waste spark. Do u have any recomendation what ignition coil do u prefer ? And please tell me the wiring diagram for the coil and link setup. Thanks
  6. Yes, i did change to falling. In order to test the ign 4. I have to turn off the ignition mode first right? And the "aux ignition #4 test icon" will appear. And we test with pwm ? And look for spark at the coil ? I will cek the volt in ign4. What is the reading if the system normal ?
  7. Dear Sir I'm using G4x civic 92 plug in. I setup for direct ignition. The engine run, but limp. Ignition no4 no spark. Coil and wiring is fine. my question is, can i alter or change the pinout for ign4 to another pin ? There is a little dent on ecu cover. Im affraid that make a short circuit. The engine fine with the distributor. Best Regards William
  8. OSF2004

    AC request

    Dear Sir I own plug in g4x civic 92. I'm about to wiring the Di input ac request. I just want to make sure before i work with it. The Di input ac request just need 12volt signal from ac botton right ? Soo basically i just can tap the cable to 12vlt signal from AC button ? Please correct me if I'm wrong. Thanks sir
  9. OSF2004

    Weird firing order

    Thank U somuch for the input. I think i will set up it right than.. Thank you so much guys
  10. OSF2004

    Weird firing order

    owww.. that's right.. i thought that is no firing order setup. I just find out, there is in the configuration set up.. Thank U so much. Since the engine already working just fine.. is it ok if i just leave it like this?
  11. OSF2004

    Weird firing order

    Dear Sir LAtely i have problem hooking my G4+ civic 92 to COP everytime i try to start cranking the engine.. always back fire Sounds like wrong firing order. Than i tried to find it the firing order. and the result is A10 for cylinder no 2 A14 for cylinder no 4 A18 for cylinder no 1 A21 for cylinder no 3 the engine start normal, idle normal, the power Good.. Is it ok if leave it just like this? I'm affraid for the long run there will be a problem.. Please advice Best Regards William K OSF
  12. Hi I need help to setup the speed reeding in realdash android In the realdash.. The speedometer didn't work.. and the gear indicator didn't show anthing.. But rest of the gauge is working Please advice Best Regards William K
  13. Thank U Simon.. sorry for silly question... Problem solve
  14. do i have to set up non driven wheel speed source ?
  15. Hi I have a problem disarm my 2D LAunch RPM. I have set up my Launch and it wont disarm. is it some setup do i miss ? here its my set up. I have check my vehicle speed sensor at Di 4 is working acurately. Please advice William
  16. Hi do i have setup the trigger calibration for my link? i did try to calibaret for the initial setup. but there is nothing change.. anything i should do before the calibrate? thanks Before william OSF
  17. OSF2004

    ECU Unlock fails

    awsome.. its working... Thanks for the assist.. and also try the real dash.. its working also... Thank U Adam
  18. OSF2004

    ECU Unlock fails

    Thanks for your advice.. will try
  19. OSF2004

    ECU Unlock fails

    here is the message i got
  20. OSF2004

    ECU Unlock fails

    Hi Sir I just bought my Civic92 G4+ Same here i cant unlock here its the serial Number : 51268 The seller in malaysia give me this NUmber " e78e888bbf235467 " Please advice Best regrad William
  21. Thanks Simon Best Regards WIlliam OSF
  22. Hi i have a little question i just Bought G4 HC92+. Can I Hook the "white wire" (output 0-5 volt) from AEM Uego wideband to Pin D14 (oxygen sensor signal) directly ? Best Regards William
  23. Thank U so much Adam.. for the assistance best Regards William K
  24. This is very helpfull.. Thanks A Lot Scott. I will do this setup for My H23. does it run with the stock distributor? so i dont have to change the the distributor with mitsu like Meshend does
×
×
  • Create New...