Spyrosgeo

Finally,steering wheel problem solved.It has electrical problem. Also my question for distance on dashboard is remaining.

I'm sorry but i forgot to ask what trigger 1 setup i must use.

Hello guys and happy new year, i have a Renault Megane II rs (2004-2010) 2.0L 163HP with FTR engine code.My concern is becauce it hasn't cam sensor. How to make it work with sequential injection mode? TriggerScope:https://www.mediafire.com/file/48q3zv29ecsnujf/MEGANE_triggerScope.llgx/file

Hello guys happy new year, i wonder if distance on dashboard will work with this this parameter on can setup(Stream 7) after taking a look at https://www.madox.net/blog/projects/mazda-can-bus/ . Also steering wheel stop working and light up steering light.The only change from g4+ file i have make is on multiplier to make the tacho sees correct. What do you advice me to do? The file:https://www.mediafire.com/file/4rlzy25wscp501u/Xtreme_RX8_CAN.pclx/file

Hello guys, I have a Mazda Rx-8 with sr20 swap. I use rx-8 alternator that use pid setup and my question is Can i use alternator control settings from mazda mx5 nb2 1.8 g4x? Thanks.

Take a look at my setup and pc log. As you can see when the e-throttle is on target at 1.6% suddendly drops at 0% and goes back to 1.6%. Also the e-throttle isn't stable under some conditions when it goes up to certain rpm. Here is the pc log: https://www.mediafire.com/file/2i3g44wbptbqagd/PC_Datalog_-_2023-08-25_9%3B10%3B34_pm.llgx/file

Hello, I have a suzuki swift and i have a problem with e-throttle.I can't match PID parameters. Can someone please help me?

Hi guys, I have a Suzuki Swift VTC (M16A) with fury g4x. I use settings from the manual and i am suffering with slow starting.With stock ecu starts regulary. I have noticed trigger 2 has slow synchronization. What can i do to start up like as before ? Take a look from triggerScope and log during cranking. https://drive.google.com/drive/folders/13NW287z1m8MBt-NhYREXIJoAN4W8yDc4?usp=sharing

Hi, I have a suzuki jimny 2009 (fourth generation) and i have a problem with the temperature gauge. In accordance with sketch on carmin I connect pin 32 with inj 5 and i use aux pwn but i can't make it work. Any idea? https://ibb.co/F80ZwXd

Hi, I have a GTRLINK-NGTRX ecu and i want to connect E-throttle. On which pins i must connect E-throttle motor?

Finaly i install a trigger disk (36-1) on crankshaft.I use hall sensor . I have 4 trigger scope on (1200,5000,7000,7700)rpm. The problem is on 7600rpm the engine is like as limiting . On the same time trigger counter is increasing and trigger 1 state (blank time). Desktop.zip Take a look what i see

On MDC i must connect on round connector ? if it is on whuch pin on round connector? What can setup i must use?

Hi, I want a clarification. I own an evo 7 with motec ecu and motec differential controllers . This devices communicate with one wire and my question is if link can communicate via one wire with differential controller .

Hello guys, I have install a altezza ecu on a 2jz engine,and i wonder if i can connect 2nd knock. Also where i can connect it. Thanks

Hi, I own a Toyota ae86 with atomX. It runs a 4AG engine with dristibutor. On trigger 1 it has 24 teeth and on trigger 2 , 4 teeth.My problem is that I can't cut 3 teeth on upper because the car must start with stock ecu due to the Race rules. What can I do to solve the problem ?

HELLO, I have storm with silver case with serial number under 10000.Ι also have aim msl .As a result i can't connect it via can.The only away is via tx,rx serial. I want to know how to set the ecu and the dash.

Hi guys, i have a AIM 1.2 STRADA 5' .I can't add gear.Ecu read it. What i must add? Can someone help me? Check the following file MXS Stradah.zconfig

Hi, we have a 2jz vvt-i engine with g4+ storm.We have a problem with vvt,it malfunction.You can see it on picture 'vvt problem'. Also i test vvt with a fury g4x and it works correctly with the same calibration. What we must also check ? BMW SPYROS 2JZ VVTI PROBLEM VVTI.llg

Thanks for your help it works perfect.

Hello , we own a LS3 engine . The engine is brand new . we have a problem with the start up . The problem is on 10 times only ones engine starts and all the other times is like ignition on the other cycle . If I stop ignition and reigition the engine starts . I use LS3 trigger mode I upload 3 triggers scopes the first file is on ognition with ignition off . The second file is on ignition . The last one is on idle . can you see any fault ? TriggerScopeLog LS3 PROBLEM CRANK NO RUNNING NO IGNICION.llgx TriggerScopeLog LS3 PROBLEM CRANK NO RUNNING.llgx TriggerScopeLog LS3 PROBLEM CRANK.llgx

This is disk on crank. Do you believe K20vtc works?

Hi, I have a Honda civic R18A .This car producted from 2004 to 2009.Which trigger mode is correct to run? Check triggerscope . TriggerScopeLog HONDA R18A 2008.llgx

I disable ignition and this is the result. Trigger Scope Log 2021-03-5 10;57;46 am.llg

I send a demo file with trigger setup and trigger scope log. What do you believe? ford puma 1.7 vvt demo.pclr Trigger Scope Log 2021-01-13 3;49;29 pm ford puma 1.7 vvt.llg

Hi and happy new year. I have a problem with ford puma 1700cc vvt. On trigger mode i have select ford duratec vct. I read correctly engine speed, the engine start, vvt works all is fine. If i stop the engine and recrank it to start sometimes start, sometimes not. When it doesn't start the engine sound like as ignition on wrong cycle. If i recrank the engine may start and work correctly. I send a trigger scope. What do you believe is wrong?