Starderby
Members-
Posts
20 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by Starderby
-
Hey there, does the Link ecu read the Factory oil temperature Sensor or do i Need to fit one to get it displayed in the ecu ? engine rb25det Kind regards
-
Hey there, from the gtr Link Manual i Found, that aux5 is a free place. I think there is a mistake in the manual , it Lists aux1 2x Times. as far as i know, Pin 113 is vtc and pin 106 is empty, this should be aux5 ?
-
Okay Thank you, i will Try this!
-
I‘m Not sure about that , i want the Hicas bulb to light up, when the waes is Working. I know there is an extra ecu for the hicas. But i‘m Not sure of it’s wired up Directly to the speedo. There is also a bulb for overheated catalytic. That would be Fine too, aswell as the ABS, Because my car has none of These left.
-
I got one more question, i want that a specific light in the speedo comes on, when the pressure switch is activated, how do i set this up ? I know my tuner lets my check engine light blink, when my car hits overboost. I want something like this for this pressure switch. i hope its understandable. Kind regards
-
Hey there, fyi, i used the top one which is fine. I now want change it to a little more "fail safe" and also to clean up wiring , i want to use the attached switch ro realize it. Before i buy the pressure switch i just want to be sure, that it will work fine. But it should work like this or not?
-
Yes I used the bottom one, will try the top one, when I got time! Thank you
-
so i did it like this, all good, if the tank is empty, or i switch , the lamp turns on. But, the DI does not switch, its always on Activated. Where is my fault ?
-
Thank you ! This helps a lot ! Not knowing about all the potential, that ecu got
-
Hey everyone, i want to give my ecu a Signal when the tank is empty(turn down boost), but also want to a have the option to turn it off by hand via a switch. So my idea was a 3 way switch, but I’m struggling where to put the DI to ...
-
Hey there, i can get my hands very cheap on a working snow performance waterpump including a tank with level sensor. From what i have read, to get it running (electrical) i need an Relais ( https://www.amazon.de/Bosch-0332209150-BOSCH-Relais/dp/B004Z0U1IW sth like this ? ) which then gets on/off switched by the Ecu via DI. Where would i wire the level sensor from the tank ? Do i need some more Hardware ? how do i set it up in the software (mainly boost controlled)? Kind regards
-
Okay, so just cut off the 12V , put the DI on and one to ground ( Sensor or car ?) , the other one just empty ?
-
Hello, i want to use my antenna switch as a map switch. I know i need to wire one to DI , but i think i get the way wrong how it needs to be grounded. is that correct way ? Kind regards car is a r33 gtst
-
done like that. i cutted the pin 30 wire and crimped it back together with the iat and wideband ground - is that okay ? thank you all
-
Hey, thanks. wideband is connected as written. The Link manual says it is factory IAT Sensor in GTRs , but I have a Gtst , so that should be empty .. Sadly I can’t turn ignition on, because when I opened the case of the oem ecu I Found a burned Platine ( I don’t know when this happened, car ran fine - oem ecu is now on it’s way to my tuner, so he can tell me which part is broken ) so I don’t want kill my link...
-
Thank you guys, so i‘m now at the car. i discovered, there is a grey wire in my PIN 36 - what is that for ? i wanted to put the pin 27 ( afm signal ) to Pin 36 and hardwire my IAT to that cable. Pin 29 should stay in position and hardwire the brown wideband wire to it. do i connect the ground wires to all to pin 50 ?? sorry guys , I’m such a noob, but it’s the only way I have to get my car to the tuner
-
Hi everyone, car is r33 rb25det. i want to wire my sensors ,that are requiered for the Link. It was planed that my tuner does this, but now it’s necessary that i do this ... i want to wire: IAT Sensor to Temp 2 (link) pin 36 wideband AEM Volt 6 (link) pin 29 Where do I put the ground wires to ? Just a proper place at the chassis ? where can put a Zada Tech oiltemp to ? kind regards
-
thank you, that helps !
- 2 replies
-
- water injection
- aem
-
(and 1 more)
Tagged with:
-
Hello everyone, i'm a newbie to the game. My car will be mapped by a professional. I think about buying an AEM Water Meth kit and wonder if my tuner can do a Failsafe by using the "Boost Safe" Wire from the AEM controller. Do i need something for this, or does he just need to wire it into the G4 ? Hope you guys understand what i mean AEM Manual
- 2 replies
-
- water injection
- aem
-
(and 1 more)
Tagged with: