Starderby
-
Posts
20 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by Starderby
-
-
Hey there,
from the gtr Link Manual i Found, that aux5 is a free place. I think there is a mistake in the manual , it Lists aux1 2x Times.
as far as i know, Pin 113 is vtc and pin 106 is empty, this should be aux5 ?
-
Okay Thank you, i will Try this!
-
I‘m Not sure about that , i want the Hicas bulb to light up, when the waes is Working. I know there is an extra ecu for the hicas. But i‘m Not sure of it’s wired up Directly to the speedo. There is also a bulb for overheated catalytic. That would be Fine too, aswell as the ABS, Because my car has none of These left.
-
I got one more question, i want that a specific light in the speedo comes on, when the pressure switch is activated, how do i set this up ? I know my tuner lets my check engine light blink, when my car hits overboost. I want something like this for this pressure switch. i hope its understandable.
Kind regards
-
Thank you !
-
Hey there,
fyi, i used the top one which is fine.
I now want change it to a little more "fail safe" and also to clean up wiring , i want to use the attached switch ro realize it.
Before i buy the pressure switch i just want to be sure, that it will work fine. But it should work like this or not?
-
Yes I used the bottom one, will try the top one, when I got time! Thank you
-
so i did it like this, all good, if the tank is empty, or i switch , the lamp turns on.
But, the DI does not switch, its always on Activated. Where is my fault ?
-
Thank you ! This helps a lot ! Not knowing about all the potential, that ecu got
-
Hey everyone,
i want to give my ecu a Signal when the tank is empty(turn down boost), but also want to a have the option to turn it off by hand via a switch. So my idea was a 3 way switch, but I’m struggling where to put the DI to ...
-
Hey there,
i can get my hands very cheap on a working snow performance waterpump including a tank with level sensor.
From what i have read, to get it running (electrical) i need an Relais ( https://www.amazon.de/Bosch-0332209150-BOSCH-Relais/dp/B004Z0U1IW sth like this ? ) which then gets on/off switched by the Ecu via DI.
Where would i wire the level sensor from the tank ?
Do i need some more Hardware ? how do i set it up in the software (mainly boost controlled)?
Kind regards
-
Okay, so just cut off the 12V , put the DI on and one to ground ( Sensor or car ?) , the other one just empty ?
-
Hello,
i want to use my antenna switch as a map switch.
I know i need to wire one to DI , but i think i get the way wrong how it needs to be grounded.
is that correct way ?
Kind regards
car is a r33 gtst
-
done like that.
i cutted the pin 30 wire and crimped it back together with the iat and wideband ground - is that okay ?
thank you all
-
Hey,
thanks.
wideband is connected as written.
The Link manual says it is factory IAT Sensor in GTRs , but I have a Gtst , so that should be empty ..
Sadly I can’t turn ignition on, because when I opened the case of the oem ecu I Found a burned Platine ( I don’t know when this happened, car ran fine - oem ecu is now on it’s way to my tuner, so he can tell me which part is broken ) so I don’t want kill my link...
-
Thank you guys,
so i‘m now at the car.
i discovered, there is a grey wire in my PIN 36 - what is that for ?
i wanted to put the pin 27 ( afm signal ) to Pin 36 and hardwire my IAT to that cable.
Pin 29 should stay in position and hardwire the brown wideband wire to it.
do i connect the ground wires to all to pin 50 ??
sorry guys , I’m such a noob, but it’s the only way I have to get my car to the tuner
-
Hi everyone,
car is r33 rb25det.
i want to wire my sensors ,that are requiered for the Link. It was planed that my tuner does this, but now it’s necessary that i do this ...i want to wire:
IAT Sensor to Temp 2 (link) pin 36
wideband AEM Volt 6 (link) pin 29
Where do I put the ground wires to ? Just a proper place at the chassis ?
where can put a Zada Tech oiltemp to ?
kind regards
-
thank you, that helps !
-
Hello everyone,
i'm a newbie to the game. My car will be mapped by a professional.
I think about buying an AEM Water Meth kit and wonder if my tuner can do a Failsafe by using the "Boost Safe" Wire from the AEM controller.
Do i need something for this, or does he just need to wire it into the G4 ?
Hope you guys understand what i mean
Oil temp Sensor Rb25
in G4+
Posted
Hey there,
does the Link ecu read the Factory oil temperature Sensor or do i Need to fit one to get it displayed in the ecu ?
engine rb25det
Kind regards