Josh Smith

yes i can

Hi adam yes was taken when the engine wouldn't start and yes i have tried that.

Forgot to add new Crank sensor and changed cam sensor I connected my scope to test for injection witch was present and checked for spark it has every thing for it to run but feel the ecu not injecting or sparking at the correct time to create combustion the problem is every time I open the bonnet the bloody thing fires up before i can get a chance to carry out more in depth scope checks. i tell ya im getting sick of it as i cant take it any where with out it not wanting to start and who wants to have a car that wont start when you want it to

Hi Guys This issue is still been a problem I suspect its the ECU. So when i first start the car in the morning it the engine will fire right up no problem. take it for a drive weather it a 5 minute drive down the road or a 5 hour drive it will run like it should. if i turn it off and re start it right away its fine if i go and leave it 20 minutes and try and re start it it will not start the the love of money. Fuel pump is new 2 years ago and has split fuel rail fuel system with yellow injectors witch have been serviced and flow tested. Coils are all genuine new 2 years ago and don't suspect this as it has no misfire to speak off. Battey is new and test's fine. I am at a loss to what this could be. Trigger Scope Log 2022-07-3 10;26;42 am.llg Tune file.pclr Will not start log.llg

Hay Adam Spoke to you on friday I have done a trigger scope file attached and also a pc log of hot cranking. can you have a look and see if you can see anything going on. Basically engine will not fire if you leave it for 5 minutes after shutdown and try and restart. but if you turn it off and start it stright back up it starts no problem. Cheers Josh hot start cranking.llg Trigger Scope Log 2022-05-22 11;13;21 am.llg also when i scope the cam sensor with my scope it is just under 6v and the link shows just over 2 volt witch is odd?

Or how to test it to identify the pinout

Hay Team Have a subaru throttle pedal Denso P/N 6010AG040 I after the pinout so i can wire in. Thanks.

Hi adam Yes i was wanting to make sure there were no issues before i started hence asking about the errors once I knew what was causing the error i added the dash and the lambda. any how its all working good now just had to remove the jumper the dash witch is a resistor.

thanks for the quick reply adam Ok so I have no connected the power tune dash and a hv electronics HV-LC1 and can t connect to them i have attached the map file Storm new setup map.pclx Ok so have the errors gone and the wide band working but no dash data when I scan the can bus nothing come up for either?

Hi team Have and issue with a new storm g4x ecu. History Old ecu was a storm g4 connected new ecu unlocked carried out ecu update setup map in run time values under can it has errors and there is nothing plugged into the b plug would be good to know what the issue is.

Hi Adam Link G4+ P&P Subaru v7-v8 ecu I have the dash wired to can 1 and setup the can 1 in the ecu to aim mxs dash port 1000 and 20 hz The problem is the dash cant see any data from the ecu. The dash is a aim brought for link its the new 7" street version Also with out realizing I transferred a page and lost all the pages preinstalled it would be good to know how to get them back Also having problems with RH cam sensor it works for a while then stops working. looses signal. have removed sensor and tested input to ecu with volt meter. re installed and rotated engine by hand and worked. then run engine and worked long enough to check tdc and carry out vvt cam test and setup on left and right sensors. then gave up the ghost. frick knows what is going on there Thanks Adam MXG 1.2 Strada.zconfig base map adam.pclr

Hi Guys I have just about finished a EJ25 Build for my wrx v8 running a link g4+ plug and play. So the factory engine runs a cam sensor on the left head and a cam sensor on the back of the head in the intake cam 2 pin AC the new build is a D25 head off a EJ255 engine and it does not run a cam sensor on the left front. but runs a 3 pin hall effect sensor is there any way i can make this work without changing the sensors over as i will run into other issues ie length and diameter. and can i run with out the front left cam sensor?? thanks

tested the boost solenoid today and fails as 18psi tried another one and same thing so problem is now solved. thanks Adam

using subaru factory boost solenoid

yes running open loop and have tried at 25hz and 20 across the whole table. my process was started at 1 bar boost and go up from there so ie as in increased from 20 to say 21 or 22 duty cycle across the whole table that is when the boost would come up and hold to 6000rpm then drop to .7 bar its like the boost solenoid can't control it i did a pwm test on the BS and its ok at low pressure but when the pressure increases in stops. can these reach a certain boost level and fail??