Jump to content

bsh

Dealer
  • Posts

    313
  • Joined

  • Last visited

  • Days Won

    9

Everything posted by bsh

  1. Little update regarding the Hella SSR relay. It still gets very hot, and after a while, it wont output full voltage... I believe I must look for something else... I just wired a normal relay so SSR relay get bypassed and pump get full voltage at about 35% injector dutycycle... Have anyone tried the AC Delco/GM fan controller?
  2. Thanks for the reply, I found a 15A diode from back in the days I raced Rc-cars with brushed motors/esc, which I soldered into the circuit, and now it seems to work, at least for about 10 mins when I tested. The diode was warm, but was able to hold it. The same for the relay, warm, but able to hold it. Stable voltage output as well. I guess I must find a more suitable SSR, but have seen other people use the Hella SSR controlling fuel pump...
  3. Hi, I setup FP Speed to control my Walbro 525 lph in tank pump. I use a Hella 4RA 007 865-031 SSR relay. 1000 hz. Problem is when the car starts, it just take about 1 min, and the fuel pump starts to see lower voltage from the relay and the relay starts to gets to hot to touch... I believed there was something wrong with my fuel pump, drawing to much current, so I scoped it and it was only about 10-12A @ about 50% duty cycle... The relay is rated 18A. Should I use a different frequency and/or a flyback diode? Any idea what can cause this? Have I got a fake Hella relay? Looks legit with the Hella stamp and part#. See scope trace:
  4. Are you using spark plugs with resistor? If not, you should...
  5. I believe you should reduce TQ, or install stronger rods.
  6. Finally sorted. Scoped every coil, all good. Hooked wideband to right bank, and it was pig rich... Injectors flow tested, all good. Checked right hand side cat, and it was blocked... Checked left hand also, and it have started to getting blocked also... Cats removed and all good. 407 hp @ the hubs (Dynapack). Owner wouldnt rev past 6200 rpm, so I stopped there. Power was still climbing, but he had windowed a block before and wouldnt more.
  7. Thanks I did a cam angle test, and it was about 2 degrees off. Yes one of the cams behave a little odd, but when I set max target at 30 degrees, they both seems to follow target. If I set at 40 degrees, one is not always following, it max at about 30 degrees. I set target to 50, and locked the dyno at 3000 rpm, it was almost 40 degrees. The other about 48degrees, which is max.Tried 60, but stopped at 48 degrees. One cam isnt always 100%, but it shouldnt have that low power?... Turned gear shift off. I just connected the hose and took some pulls to 4000 rpm. Seems like the problem moves closer to 4000 rpm now. Only 150 hp... Car idles nice. I think I will scope every coil to see if there is some that have some issues/bad connection. I only scoped #1. Any more ideas?
  8. Hi, I just installed the ecu on a early 350Z with intake VVT only. Car is supercharged with no pressure (hose to intake is disconnected), 630 cc injectors. New coils and spark plugs gapped to 0,6mm. Power drops after 4500 rpm... See dyno chart. I used a ramp rate of 500 rpm/s. at the dyno. Afr is about 12.5-13. Both cams follows target. Log file shows steady timing. Knock disabled. I have checked with a timing light that timing is stable from low to high rpm when locked. I also scoped the coil #1 primary circuit with my 4ch Picoscope. There is about 2V power drop at the ground, but I adjusted dwell until coil was saturated as a quick fix. See scope trace. Anyone have any idea what might be the problem with the low hp? Am I missing something essential here? I dont want to apply boost before I feel the NA power is good enough... Thanks 350Z 2000 rpm - 5000 rpm.llg Obrestad 350Z.pclr
  9. bsh

    350Z+ G4+ questions

    @Adamw Hi Adamw, can you also provide me info regarding get rid of the lights in cluster after installing the 350Z plugin? Thanks.
  10. Do you share the mapsensor vacumhose with something else? You are using the ecu internal map sensor?
  11. Do you have any trigger errors @7000 rpm?
  12. bsh

    LS3 cam sensor

    Thanks Yes will try swapping wires:)
  13. bsh

    LS3 cam sensor

    I have them wired as per Stevieturbo`s diagram as it was the on I found on the web. I will try your pinout Adam, but the LS3 isnt listed in the text. Your wiring recommends +5V, Stevies +12V. Why are you using +5V? GM says 12V for their sensors. Btw I have the Grey sensor.
  14. bsh

    LS3 cam sensor

    Hi, I just wired a Storm to a LS3, but cam signal is dead, about 1,8V all the time. Crank is fine. We suspected the cam sensor was dead, and tried another one they had and still the same... I just wired in a GT101 and all ok. Engine started right up. I suspect that the sensor pinout I found is wrong, or both sensors are dead, which is unlikely...? Anyone have a 100% correct LS3 cam sensor pinout they want to share with me, as I would prefer to use the oem sensor? Thanks
  15. SOLVED... Can H and Can L was put in wrong place in Connector...
  16. Hi, Anyone have a detailed how-to setup for both the AIM Race software and PCLink software? Tried With some old guides I found, but cant get it to work... Thanks
  17. If Your afrs are fine and voltage to Your coils under load are fine, and Your coil grounds are fine, I still suspect you are having a spark misfire. Are you running the vw 4 pin cops? Adjust gap to 0,50 mm and see if it makes a difference. Tip: You should type in English so all people here do understand:)
  18. bsh

    trigger setup

    Ecu settings- Triggers. See below. Choose Your sensor, either hall or reluctor. Are you running wasted spark or Direct spark? Sequential fuel?
  19. Hi, I dont know what ignition you are running, but I would try to lower the gap on the electrode on Your sparkplugs to about 0,55-0,60 mm.
  20. bsh

    Idle up and down!!!

    Check that your ign angle is pretty steady@idle. Also check that your afr are pretty steady.
  21. Do you get any trigger errors while this happening? Press "R" and look under "triggers" and see if the trigger error counter are counting while revving to 6000 rpm.
  22. Does the triggerscope show both crank and cam signal? Under runtime values, are both trig 1 and trig 2 showing a green OK? Have you unlocked the ecu with the password from your dealer? (will not start without ecu enabled)
  23. bsh

    Volvo V70 Petrol 1998

    I have installed and tuned both Volvo (60-2) 5 cyl and Audi 5 cyl (135T), but only manual gearbox. I believe you must piggyback the auto gearbox.
  24. Some more pictures/info:http://gatebil.no/roger-halands-toyota-starlet/
×
×
  • Create New...