Jump to content

Sutkale

Members
  • Content Count

    155
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by Sutkale

  1. Sutkale

    Ethanol Content Clamp Function

    BTW is there reason why ethanol content sensor reads 3-5 % lower ethanol content than in reality. Running VP´s C85 race ethanol and Continental sensor reads only 80-81 % ethanol content. Same with pump E85, but 1-2 % lower ethanol content. C85 should be exactly 85%.
  2. Sutkale

    Blown engine!

    According to the log files I see no reason for bad tune as reason for blown engine. What actually happen to the engine - no info on that. Is reference ignition ok?
  3. Sutkale

    CAN 1 and 2 in ViPec i88

    Thanks. Gotta check that. I think this is quite first versions of i88. If so, no wonder why having issues connecting to PMU unit via CAN 2.
  4. Sutkale

    CAN 1 and 2 in ViPec i88

    Hi, Is 6 pin round connector at ECU end CAN 1 and CAN 2 is DI 9 & 10? Thanks!
  5. Sutkale

    Ecu to pdm via can

    Thank you Adam, appreciate! I´ll make the set up as adviced and be in contact if results are not as they should be.
  6. Sutkale

    Ecu to pdm via can

    I am also in the heat of installing my PMD / PMU and configuring Vipec i88 and Ecumaster PMU accordingly. I want to control second fuel pump based on TPS % position, i.e. 2nd fuel pump should turn on when TPS is above 25 %. How to configure multiplier / dividers / offsets that PMU would see TPS % as it should (from 0 % to 100 %). And some basic questions regarding the CAN: 1) Should "Frame" include only one parameter, like fuel pump in picture above? 2) Should every "Stream" to be configured under single ID or is ECU transmitting all the data under on ID?
  7. Sutkale

    Motec PDM to Fury CAN

    Hi, Sorry for stealing the topic, but my post is kinda of some nature than this one. I just purchased Ecumaster PMU / PDM and would like to control it via CAN from my Vipec i88 (Link G4+ software). What are the basic settings in ECU, for example, controlling the fuel pump / fan / etc. stuff by PMU that are now connected straight from AUX outputs? Step by step instructions please..
  8. Sutkale

    Volvo V70 Petrol 1998

    I am running Volvo 4 cylinder white block engine with Vipec/Link ECU, so no issues to control 5 cylinder white block engine that is basically identical to 4 cyl version. Crank is 60-2 teeth, trigger on cam - so basic set up with that respect. Autobox control would be an issue since it has its own ecu and it needs certain info from stock engine ecu to run properly (torque reduction during shift, oil temperature control etc.). I think you can get this on the road, but do not know how the autobox would hold. I´ve hear guys been doing set ups like this, but autoboxes haven´t lasted for the reasons above. I agree, there would be market for this car in Europe.
  9. Did few days ago individual cylinder tuning (fuel) and noticed that only primary injectors are controllable. Any ideas when also secondary injectors can be tuned per. cylinder? Or is this doable at all?
  10. Sutkale

    Individual cylinder tuning and staged injection

    Hi Scott. I´m using sequential / staged. Since the correction applied only to primaries, had to use quite high numbers to get desired results.
  11. Sutkale

    What is new with PCLink V5.6.1.3098 Firmware

    Any ideas when we get firmware update that would support injectors over 3000cc at modelled fuel equatation? Running staged injection with 1200 plus 2300cc injectors meaning cannot benefit from VE fuel calculation.
  12. Resistor pack with link G4+?
  13. Sutkale

    FIC 1450

    What Link ECU do you have?
  14. Sutkale

    Graph Issue PC Link

    I have an old HP EliteBook 6930 and running Windows 10. I downloaded and installed an upgrade to OpenGL from this site and the graph works now. http://danielkawakami.blogspot.co.nz/2014/08/gma-4500-series-feature-pack-for.html
  15. Sutkale

    Link Thunder Load Axis issue

    I´ve got exactly the same appearance as above. Running Windows 10.
  16. Sutkale

    Link Thunder Load Axis issue

    Here´s a screenshot from the graphic view that I see:
  17. Sutkale

    Link Thunder Load Axis issue

    A bit different issue but with the newest firmware. I can´t get graphic view visible at the same time with grid view on fuel table or ignition table etc. And while looking at the graphic view only, the visibility is very blurred and can´t see any values. This all when offline. Haven´t tested online yet.
  18. Sutkale

    Traction control

    Thought to post a video from my traction control test a few weeks back. 1.5 bar low boost on wet and cool road (+6 C) at 2nd gear. This is fwd car with 2.0 litre engine equipped with Garret GTX4202R turbo. Highest power level 916 hp at crank so far @ 2.8 bar boost. Should traction control sound like this? Really heavy banging in my mind. However, front tires stays within set 5 % slip to rear tires, so it really works even on very slippery conditions. Traction mode is "Fuel%Cut".
  19. Sutkale

    Traction control

    Files sent in two separate mails.
  20. Sutkale

    Traction control

    Hi Guys and thanks for watching, Here´s the screenshot from TC settings, slip threshold is 5% at every gear: The log file is too big to attach or am I doing something wrong. It´s quite big, over 40 minutes...
  21. Sutkale

    VE numbers seem high at idle

    I´m running at ridiculously low numbers at idle, around 5. All injector data should be correct, but I guess very cammy engine with minimum vacuum causes this.
  22. Sutkale

    Updating to Thunder

    Hey. Maybe its time to update my Vipec i88 to Link G4+ Thunder. I suppose looms A & B from Vipec i88 fits straight to Thunder. C&D looms needed? Anything else to consider?
  23. Sutkale

    Updating to Thunder

    One thing came to my mind with respect Thunder. Is new ECU / software capable of running larger than 3000cc injectors at modelled fuel equation? Would be nice to run on pure VE fuel calculation. Currently the software does not accept larger than 3000cc injectors at modelled fuel equation. I´m running sequential / staged injection where primaries are 1180cc and secondaries 2300cc. Had a quick look to Emtron fuel calculation whereas user may configure both staged injector sets individually.
  24. Sutkale

    Updating to Thunder

    Sounds like an easy upgrade, thanks Dave!
  25. Sutkale

    Some trigger issues

    Hi, Have had some unsolved trigger issues for a long time in certain conditions but now thought to tackle the issue, since it somehow got a bit worse when I relocated the battery. The symptoms are roughly as follows: 1) Revving the engine standstill, trigger error comes in at app. 7000 rpms, causing 10-15 errors -> rapid rpm ramp rate 2) First gear, trigger error comes in at app. 7500 rpms, causing 10-20 errors -> still rapid rpm ramp rate 3) Second gear, trigger error comes in at app. 8000 rpms, counting up to 10 errors -> slower rpm ramp rate 4) Third gear and higher, the engine can be revved up to 9500 rpms and no trigger errors if there´s grip available and rpm ramp rate isn´t that high. Trigger mode is MultiTooth/Missing, Tooth count 60, Missing Teeth 2, Trigger 1 type Reluctor. Trigger 2 type is Optical / Hall. Reluctor sensor is Siemens 2 wire sensor. Changing trigger 1 filtering higher will make the issue even worse and adjusting trigger arming threshold does not really help, using now 2,5 - 3 volts at higher rpms seems to be the best option so far. It is obvious that rpm ramp rate has something to do with this since the things get worse when rpms rice fast. Any ideas how to get forward with the issue? Or is this a mechinal and related to trigger wheel shape especially to missing teeth shape? Just got a cheap picoscope on my hands and thought to play a bit with it, if that would provide me some help and see how the signal behaves when the issue occurs. I don´t know if ECU´s own trigger scope is capable of recording signal on high revs? I attached a screenshot from the signal taken by ECU´s own trigger scope when trigger is error free.
×