Jump to content

Cnstman

Members
  • Content count

    34
  • Joined

  • Last visited

  • Days Won

    1

Cnstman last won the day on June 20

Cnstman had the most liked content!

About Cnstman

  • Rank
    Advanced Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Cnstman

    Problem with TPS in G4+ecu subaru plug&play

    subscribed. I had this issue once on my 04 USDM STi. I did both of the ethrottle relearns and so far it has not came back.
  2. Cnstman

    [UPDATE] PCLink 5.6.5.3338b Released

    wondering the same thing
  3. Cnstman

    Cruise Control?

    The cruise control feature works great, however I have tried and tried, but I can't get the cruise control light on the dash to indicate when the system is enabled, or active. Any advice?
  4. Cnstman

    windows 10

    No issues with Windows 10 here either.
  5. Cnstman

    Subaru I88 V10 plug-in DI11 input?

    Ok, thanks for all the help. I do have anvolt 11 working, I just could not remember which pin its wired to. Having access to anvolt 12 is a help as I needed one more input.
  6. Cnstman

    Subaru I88 V10 plug-in DI11 input?

    Thanks. Those diagrams show anvolt11 in 2 locations.
  7. Cnstman

    Subaru I88 V10 plug-in DI11 input?

    Per my first post I have a 2004 usdm sti. Thanks for the info. I also have the smaller 4 pin expansion harness. I can't find the wiring pin out for that in the help file. Do you have that?
  8. Cnstman

    Subaru I88 V10 plug-in DI11 input?

    Simon: What about AN Volt 12?
  9. Hello, I have a Subaru I88 V10 plug-in for my 2004 USDM STi, and I need another Digitial input. The help file does not show which wire in the expansion connector to use for DI11. I see DI11 in the inputs, just need to know what wire to use. Thanks! Aaron
  10. Cnstman

    Windows 10?

    I upgraded to windows 10 and have had no issues. thanks for the input.
  11. Cnstman

    Vi-pec i88 connecting to IQ3

    My IQ3 Logger dash works great. Below are the settings I was advised to use by Racepak. They don't monitor their forum much, but the tech dept. got back to the company I bought the dash from with-in 30 min and I had my answers. Can 1Data Rata 1MBPSCAN ID 1000Data Direction ECU TransmitTransmit Rate 20 or 50 is avail.
  12. Cnstman

    Windows 10?

    Has any testing been done with Windows 10 and the new PC Link software?
  13. Cnstman

    Ethanol Sensor DI vs A4Volt?

    I have the siemens ethanol sensor which according to the help file requires an external resistor. Can this sensor be shared with no external or pull up?
  14. hello, I have the output wires from my zeitronix ethanol content gauge hooked to ANVolt 4. Its calibrated correct, and the ecu displays the same value as my gauge. I see with the new firmware there is a specific DI labeled ethanol sensor. How can I tell my ecu to use anvolt 4 in stead of this DI? My ecu is a 2004 usdm Subaru Sti plug in. When I go to the MISC runtime page the ethanol % always shows the fault value assigned in the DI for ethanol sensor, it does not show my ANVolt 4 value which is correct. Liikewise my startup tables are using the fault value data vs the correct data from ANVolt 4. If I need to re-wire, which pin on my ecu is the ethanol sensor DI? the help file does not provide this info. thanks Aaron.
  15. Cnstman

    Cruise Control?

    Finally have my car running again and I am playing with this new feature. Can you explain how the cruise control should work on my 2004 Usdm Subaru sti? I can get it to work from time to time but have to hold in the button on the stalk and push down and release the button just right while still pushing down then release. I can't get the accelerate or coast functions to work at all. Any help would be appreciated.
×