Jump to content

Top Tune NZ

Dealer
  • Posts

    138
  • Joined

  • Last visited

Everything posted by Top Tune NZ

  1. Hi chris the std cas sensor runs fine on the 4age i do not see any advantage in running the cank trigger unless you are building a super high reving ing drag engine over 10,000 rpm
  2. Link G4 Atom nissan vh41
  3. Link G4 storm 13b mazda rx7
  4. Link storm G4 Rb25 Link storm G4 lexus non vvti
  5. link g4 storm 2jz non vvti 35/40 750cc injectors 2jz-base-storm-3540-750cc-inj.pcl
  6. link g4 Storm 2jz base map with no idle speed controler
  7. HELLO EVERY ONE MY NAME IS ROSS HONNOR I OWN AND OPERATE DOBSONS DYNO TUNING IN NEW ZEALAND, I THOUGHT I WOULD START THIS LINK TO HELP THOSE OF YOU THAT ARE A BIT LOST AND WOULD LIKE A BASE MAP TO HELP WITH SETTING UP. THE MAPS PUT ON HERE ARE SOME OF THE CARS WE HAVE TUNED I TAKE NO RESPONSABLITY FOR YOU BLOWING UP YOUR CAR BECAUSE YOU HAVE DONE SOMETHING WRONG OR NOT HAD IT TUNED CORRECTLY. THESE MAPS ARE INTENDED TO HELP YOU. PLEASE DONT PICK THEM TO PIECES AND ABUSE ME IF YOU FIND IVE MADE A MISTAKE. AS IM PROBLERLY LARGER THAN YOU. YOU ARE MORE THAN WELCOME TO RING ME OR EMAIL ME ABOUT YOUR SET UP I WILL ONLY CHARGE YOU IF YOU KEEP RINGING MY WORK HOURS ARE 8AM TILL 5PM NEW ZEALAND TIME PLEASE DONT RING ME OUT SIDE OF THIS TIME WITH OUT ARRANGING IT WITH ME FIRST. MY MOBILE NUMBER IS 0064 21 754832 FOR INTERNATIONAL CALLS ph 021754832 for new zealand customers or my workshop email is: [email protected] WEB SITE: face book Dobsons Dyno Tuning
  8. cold start requires about 15%richer and start engine with a closed throttle
  9. drop me a email i have one for you [email protected] cheers ross
  10. i have this issue also and have told simon early last week
  11. some advise mate: you are going to make it hard for any tuner to get correct if you keep tuning your car. The dead times are one of the last things you adjust after you have set up the master fuel and then tune each zone in fuel settings then ignition timing then go back to the fuel again to double check it. your battery voltage should be very stable during this peroid when you have finished tuning the fuel and ignition then disconnect the alternator and hold the revs stable lets say 2000 rpm as the voltage goes down then adjust the dead times to keep the afr stable to speed this up you can turn on your lights it should only take about ten min to do this after you have done this then go into your accel and then cold start settings then set up the fan and load fuel gains etc hope this helps cheers Rosss
  12. Previously matt henderson wrote: hi ive just wired a link extreme to a boss 260 engine in a mustang having problems getting it to run right have counted trigger wheel 36 tooth one tooth missing the engine will run we got timing set but it backfires out the exhaust. had a local guy who installs and tunes alot of links take a look and he seems to think that the crank sensor is not reading the missing tooth properly and is therefore backfiring. any ideas on the cause or remedy to this fault have you scoped the triggers to check what is happening?
  13. Previously Nate Chaisson wrote: Here are some pictures. It is on a '96 Miata running 8psi. Can someone please help me identify it. I would like to know how I can tune it. http://www.flickr.com/photos/u_have_saved_me/6228867377/ http://www.flickr.com/photos/u_have_saved_me/6229383706/ Thanks, Nate it is a older model link and is tuneable by using a hand controler these are not available from link any more but sometimes can be found on trademe.co.nz and ebay i have a spare one also but would want at least $500 nz dollars for it plus freight cheers Ross
  14. check you are using ignition switched 12v for the relay power. and not looping the main 12v over on the relay or this will cause a back feed like you have also dont loop wires from one relay to the next relay confusing aye
  15. six inkectors is no problem, yes you can run as many maps as you like just load each one as you want it from your lap top or you can set up a couple to work from a digital input yes you can have ignition cut instead of fuel give me a call if you like on 06 7548336
  16. you can over come this by using a di as a anti theft switch to kill the engine with out turning off the ecu.
  17. try rolling back to your old firmware if you found it easier i would use the bosch knock sensor it just needs to be tight there is not a spec for the tension. this sensor gives a nice stable knock signal the orientation of the wiring shouldnt matter on the sensor
  18. not really untill you get down to about 6 teeth and only then at real low rpm around idle and cranking. i wouldnt go less than 12 on your aplication
  19. dont try a nissan as it will be too unstable with the timing chain and dist gear both having play we have seen honda and toyota dist grafted in to minis a series motors and the work well
  20. can we have lamda instead of afr ? i know this is a big job but it is very much needed with all the different fuels we are tuning
  21. i have asked dave at dtech to email you
  22. email dave at dtech motorsport he is another dealer and imports this dashes
  23. hi the 36 -4 crank trigger will work fine well over 9500 rpm cheers ross
  24. you can use the race pack dash now using a adaptor from them to plug into the current link dash port if needed
×
×
  • Create New...