Jump to content

Simon Kribstock

Members
  • Posts

    22
  • Joined

  • Last visited

Everything posted by Simon Kribstock

  1. Any ideas why I would be getting a hard ignition misfire at around 1 bar of boost? Ran fine up to 1.3 bar with the coil pack ignition 3.56ms misfire, new coils and boots.llg
  2. Recently converted from coil pack to coil on plug. Wanted to confirm my changes to the ignition settings. I've modified my dwell control table to correlate with new coils. Do I change "ignition mode" from wasted spark to direct ignition? Should I re-calibrate my ignition delay? Open my spark plug gap? Had it closed down to .024" from .030" while using the wasted spark set up.
  3. Anyone have a 2D or 3D ignition dwell table for 2011+ STi, black ignition coils; PNL 22433AA602. I recently converted by 99 STi to COP.
  4. I believe I wasn’t giving the stepper valve enough time to reset, making it start in random positions. I currently have it set up to reset at key on and wait for the tach sweep to finish before cranking. Key off reset was still a bit a bit wonky for me so I just stuck with key on.
  5. Haha ok that is what I should’ve asked; if the clutch even sends a signal to the ECU on a standard Subaru. I was thinking it was a pre-wired input like the power steering switch, ac request, etc. I must’ve entered it with the intention of wiring it to DI5. Thanks Adam.
  6. no, it doesn't change. tune attached 4bar MAP, quick spool, popping flames flat boost.pclr
  7. 99 STi plug-in g4+. Setting up my launch control. Would like to use, or at least try, my clutch switch as the activation control. I believe DI5 was the default input but I'm not 100% sure. It doesn't respond in the runtime window so it obviously won't arm. I know the switch works because I originally had it bypassed for no-clutch starts and now it won't start unless depressing the clutch. Any ideas?
  8. What does compressor surge look like on a data log graph? At about 7000rpm, my MGP/MAP spikes, fuel leans slightly (despite adding fuel) and power falls off. No knock or fuel/ign cut. Turbo is a VF48 with a billet compressor wheel.
  9. I suspect a sticky or failing valve as well. Firmware is 5.6.5.3338 Here is my tune. I'll have to make an idle log. 60 degree idle map with idle ignition ... cl idle.pclr
  10. Having this same problem. This is frustrating as my engine idled just fine with a standard ECU. Is buying a new IACV the only solution that has worked for everyone?
  11. Attempting to tune my idle base position table in open loop. I follow the OL procedure, achieve a suitable idle, save and store. But when I turn off and restart the engine, I have to completely change the idle base map values. Car is a 1999 Subaru STi with a stepper idle valve.
  12. Lock/unlock issue has been resolved. Could updating the firmware after unlocking the ECU cause it to request unlocking again? Either way, it's good now. I also resolved the the 5v supply error as well by properly pinning my MAP sensor Thanks Adam
  13. Subaru v5 STi, WRX6 Plug-in ECU I have disabled the ANv4 (n/b o2) Error low fault detection (set to 0v) but the ECU is still throwing fault code 20; below error low value. Any ideas?
  14. PCLink v5.6.5.3338, Firmware 5.6.5.3389 I have unlocked it once I noticed tonight I had a fault code 74: analog 5v supply error. Not sure why I didn't see that yesterday. Checked the runtimes screen and it was fluctuating below 1volt. Only wiring modification was s 01-07 WRX STi Omni 3bar MAP sensor so I disconnected it and everything seemed cured. I may have used some bad pinout info from a unnamed forum . I'll re-pin tomorrow and see how it works.
  15. I set AN temp 3 to IAT and sure enough it works. Matches ECT +/- 2 degrees. With that said, I’ll wire my GM IAT, mounted just prior to the TB, using the OEM IAT circuitry; unless otherwise advised. I’m curious about AN temp 3 on my expansion connector now. How will that input work?
  16. My IAT sensor is separate from the MAF. I have an RA Limited STi; maybe that’s the difference?
  17. Erratic sensor readings .MOV Just plugged in my WRX6 plug-in ECU for the first time. Upon switching the ignition to "on", engine "off", I immediately heard my IACV cycling. I connected to my ECU via PClink, and noticed erratic readings. I updated the firmware and readings remained. I flashed a tune with the proper calibrations for my MAP sensor, injectors, etc. and performed a TPS calibration. Erratic sensor readings remained and now included an erratic TPS signal. Another issue I'm running into is a repeated request to unlock the ECU. Any ideas? Attached is a video screenshot. Please excuse my post edits haha. Haven't figured out how to remove dupilcate videos
  18. Would the OEM IAT be routed to pin B136-19 on the main header? The manual says that pin is AN Temp 3 (V1.1 PCB only),which to me, suggests the OEM IAT but I have no way to confirm. Nothing is configured for AN Temp 3 on PCLink as this input is also on the expansion connector.
  19. I have a v5 STi with OEM IAT. I bought a GM IAT and installed it just before the throttle body. Should I use the expansion connector or should I snip the OEM IAT and wire it to the GM IAT?
×
×
  • Create New...