Jump to content

azmak

Members
  • Posts

    69
  • Joined

  • Last visited

Everything posted by azmak

  1. I was wrong. I have been redoing it in open loop since a while ago. Thanks again for your prompt guidance.
  2. At low turbo boost (about 190kpa) it is stable, but as I turn it up it hunches. Please look at the data file and log file and instruct me if there is a problem. Log - 2023-05-27 11;34;59 am.llgx
  3. I have already replaced it with a MAC 3 port solenoid because I realized that the factory solenoid does not do what I want. Thank you very much. I will use it as a reference.
  4. Please give me two instructions about G4X RB26DETT. (1) The turbo boost is not adjustable. (2) When I want to set the key ON sweep of the tachometer to 10,000 rpm, I have to input 12,200 to PC-LINK. What is the reason for this error? I have attached a pclx file for your review. BNR32 20230526.pclx
  5. Hello everyone. NISSAN BNR32 RB26DETT G4X plug-in is used. Is it possible to control the stock Boost Control Solenoid? If so, can it be controlled up to about 230kpa?
  6. Thank you for your guidance.
  7. Hello everyone. Tell us about it. The car is a BNR32 (RB26DETT). I would like to copy the data file created using the G4+ plug-in to the newly purchased G4X plug-in. I cannot open the G4+ data file in PC-LINK of G4X.
  8. We did not include a target boost. I was careless. Thank you for pointing this out.
  9. SR20DETにGreddyウエストゲートを装備。 ブースト制御は柔軟ではありません。 MAPに100を入れるとあまりブーストは上がりませんが、MAP値には若干反映されるようです。 別のバッテリーを使用してソレノイドバルブを常時ONにするとブーストは止まらずに上がっていきます。 何が間違いなのか分かりますか?
  10. I see. If that's the case, I don't blame you. I tried "pre-crank prime" as well as many other things, but still no improvement. I will consider measures to increase the cranking speed in the future. Thank you all very much.
  11. Thank you for all your help. I have saved the Log at startup 3 times in a row. Please take a look and give me some guidance.
  12. I would appreciate any guidance anyone can give me. Cranking time is too long. The engine starts after about 2 seconds of turning the starter. I have changed fuel settings, cold start, etc. but no improvement. Please let me know what is wrong. It is a 350Z (VQ35DE engine) with R35 GT-R injectors and HKS supercharger.
  13. I'll try to rework the wiring. Thank you very much.
  14. GT-R LINK Plug-in. The 6 on the ECU PIN is the engine fan. The 6 of GT-R LINK is assigned to Aux-Inj8. Please tell me how to make the engine fan work. Is it possible to control it by temperature? https://imgur.com/3ux63C9
  15. azmak

    Setting the rpm limit

    When I had the stock ignition coil, the RPM limit was exactly as set. After replacing it with an aftermarket multi-spark ignition coil the other day, the RPM limit started to shift. Do you think that is the problem?
  16. azmak

    Setting the rpm limit

    Thank you Adamw. I have attached the log file for you to verify. Log 2021-06-20 3;24;46 pm.llg
  17. こんにちは、みんな。 RPM制限は9500rpmに設定されていますが、8200 rpm〜8300rpmでアクティブになります。 私は何が間違っているのですか? 20210620-1.pclr
  18. I understand. For now, I'll use that method to overcome the problem. Please let me know if you get any new information. Thank you very much!
  19. Thanks for the information. I could not set the font size to more than 18. I tried reducing the size of Km/h, but still could only set the number size to a maximum of 18. Please let me know if you have any new information. Thank you all.
  20. As you can see from the image, the font size for speed is smaller. Why is this? This car is a 5-speed manual.
  21. While I was touching RS3, the font size of the speed became smaller. Even though I didn't change the font size. The font size was 18 before and is still 18 now. Also, is it possible to get the "N" to display when the gear position is neutral? I have incorporated a neutral/park signal into the digital input of LINK.
  22. Thank you all. And thanks for the interesting info!
  23. Nissan Skyline BNR32. LINK plug-in and MXS1.2 Strada. Obtained from LR wheel speed sensor. Speed is displayed on PC-LINK. But speed is very unstable. MXS1.2 Strada display is still 0km/h. I need to know how to set it up.
×
×
  • Create New...