Jump to content

o_dd

Members
  • Posts

    28
  • Joined

  • Last visited

Everything posted by o_dd

  1. It worked fine. Thank you very much!
  2. What are the CAN settings? I changed from G4+ to G4X I am using AEM CD7 for display. The lambda trim that was displayed correctly on the G4+ is now showing abnormal values. Are the settings different on the G4X? If it is normal, the value is displayed in the range from -15 to +15.
  3. o_dd

    Trigger error?

    Absolute pressure 2.5bal showed an error when the plug was old
  4. o_dd

    Trigger error?

    Coils and plugs function properly Coil noise is addressed The running log records 19000 rpm, but the ECU stats do not record it why?
  5. o_dd

    Trigger error?

    Yes, sir. We've got enough fuel. Ignition system is stock. Boost pressure is 3 bar absolute. Are you saying that there is a possibility of a trigger error from misfiring? What measures have you taken?
  6. o_dd

    Trigger error?

    The error doesn't occur every time, but it often does under heavy load. I'll check the errors in the trigger scope. Thanks.
  7. o_dd

    Trigger error?

    I had the same symptoms when I used the Nissan crank trigger before. At that time, I replaced it with an AEM trigger plate to counteract the problem. But this time, I don't know how to countermeasure it. The number of teeth on the crank trigger plate of the Lancer Evolution 9 is 2. When I reduced the number of teeth on the Nissan, it stabilized, but for the Mitsubishi, should I increase the number of teeth?
  8. o_dd

    Trigger error?

    Car model is Lancer Evolution 9. EVOLINK plug-in is used The engine rpm becomes abnormal under high load and the rpm limit is triggered. Is there any countermeasure?
  9. Hello! Can the electric fan control of toyota in this image be used? PWM control module
  10. o_dd

    AEMNet CAN bus Gauge

    Hello 30-0312-I want to use AEMnet CAN Is it possible to connect with Link Ecu and CAN?
  11. Thank you BarendB I wanted to control the alternator with Link. I look for the alternator who taught me
  12. Hello The MX5 alternator is PWM controlled with reference to this thread. But the voltage is not stable Is there a map that can be helpful?
  13. o_dd

    Mazda MX5 VVT

    Thank you Simon There is a possibility of initial failure Talk to the dealer you purchased Isn't it a mistake of Di3 input instead of Di1 input?
  14. o_dd

    Mazda MX5 VVT

    Hello I tried to run EVO Link (I-III) on MX5 But the result didn't work as it was in the past When I connected my WRXLINK (7-9) it worked fine But EVO Link (I-III) does not work properly Is this a malfunction? Does EVO Link (I-III) convert trigger input on the bottom board?
  15. o_dd

    Mazda MX5 VVT

    The number is not 0 but is a modified number
  16. o_dd

    Mazda MX5 VVT

    Yes, the enter key is pressed I'm verifying that the field is blue I remember in the ECU after that
  17. o_dd

    Mazda MX5 VVT

    Thanks adam I made the offset 0 but it was useless I want to adjust it because the timing is off like the image Changing the trigger offset value does not change the timing I do not know why the timing does not change Of course, it is memorized by ECU with return key and F4 key
  18. o_dd

    Mazda MX5 VVT

    I'm sorry The model is NB8C and the engine is BP-VE Is there any information about this engine?
  19. o_dd

    Mazda MX5 VVT

    Hello I am looking for an MX5 VVT basemap I want you to tell me that the trigger offset is not known Thank you
  20. Can I use expansion connector Ign5 to use direct coil?
  21. Hello I am using EVO3LINK I want to use 4 ignition coils. Can I change the IGN4 ECU hold power and use it for ignition? Thank you
  22. o_dd

    Tachometer key-on sweep

    Oh, that's a shame ...
  23. Hello Does tachometer key-on sweep work with CAN connected dash display? I am using AEM CD-7 but it does not work Thank you
  24. o_dd

    AEM CD-7 digital display

    Dear Adam Thank you for your wonderful work The uploaded file was an old thing by mistake Currently all mistakes are being fixed The set file worked perfectly I am happy and I can not sleep today.
  25. o_dd

    AEM CD-7 digital display

    Was the file I uploaded wrong? Or was it impossible to broadcast an analog voltage?
×
×
  • Create New...