Simon_s13

Hi, I'm having some issues with my base map. I just installed a new set of injectors(1400cc). I'm using the dead time table provided by the seller. The VE at idle numbers are very low(10) and it is still too rich 0.88 if the engine is warm and running more than 15 min. When the engine is cold after start it all looks ok but as soon as it gets hot it gets richer. With operating temperature it is lean for a few seconds after the engine starts and then it gets richer. I have tried to spot the problem with the logs but I can't, could someone take a look at my log and base tune to see if they can spot something wrong?. 1400cc rich.pclr 1400cc lean to rich.llg

Hi Adamw, I replaced the sensor and it works fine now thanks for your help, not sure if it was faulty or fake but I bought an innovate sensor(SE1004S), at least it should be genuine sensor.

Hi. I just fitted a continental 13577379 flex fuel sensor, the link storm is reading between 30 to 32% of ethanol on the pump fuel. The tank was drained today and I put in a new fuel (99 oct E5) and it is still reading over 30%.

Ok thanks for the explanation I understand it now.

Thanks for your quick response Adamw, The RPM limit is 6500 rpm as you can see on the attached image Why does it activate the limit at 6087rpm? I'm a bit confused with this.

I was on the dyno this morning and I found that the car was losing power. I went through the log and I found "Limit IGN Trim -5". it may sound stupid but why does the ECU activate it? The engine wasn't knocking, ECT and IAT ign trim were off. After a few runs I have seen it twice. Thanks in advance 605-1.llg

Thanks Adamw all is working now

Hi I’m running a link Extreme G4+ and I am trying to use a can message as an input to activate and deactivate the launch control and traction control. I believe that the G4+ does not allow me to do it but I like to ask if it will be possible. I have created the message already ID 1100 B0 : traction control B1: launch control

it works at it should be after the software update, Thanks Adam

If there is only positive going through the valve before the ecu is powered up it should make a single “click” noise, depending on the frequency written on the ecu the noise changes so it means then the ecu has got power and it is activating the idle valve. Also the engine starts and the fuel pump is priming at the same time as the idle valve is making the noise before I start the engine.. The Idle valve and the ecu have a different power feed but same time activation. I haven’t adjusted the idle control yet in case the ecu gets damaged. I have tried once to start the engine with the idle valve activated and connected and it seems to work, when the engine is running I can hear it working.

I have the ADU 7 connected to my link storm and all works fine. You can also connect the link straight to the ADU on “CAN 2” without an external resistance, ADU software has the option to add the can bus terminator. But you need to activate it. I can copy the last version of my ADU to confirm you all details if you need them to run your one but will need to be during the weekend.

I did the PWM test and it does work fine, as you can hear on the videos the idle valve is priming as the fuel pump when the ignition is on. The diode was removed before the videos, it does actually the same with and without diode. The fuel pump stops just before the idle valve. https://youtu.be/DsAuAXgMncU https://youtu.be/s9O9tbAywGo noise.pclr

Yes, it is powered by the PMU once the ignition is on, it also powers up the ethanol content sensor(it is not connected yet) I will remove the diode and do the PWM test on Saturday will let you know the results.

Thanks Adam, I connected one terminal to aux 8 and the other one to 12V positive Should I remove the diode? I will try to do the PWM test and I will let you know I didn’t actually try it.

Idle solenoid Hi, I have set up the idle control valve in my car using the AUX 8 on my link g4+ Storm. The idle valve is the ford version like the image. After selecting on the PClink on the AUX 8 ISC solenoid with 100 hz of frequency I went to idle speed control menu I chose open loop sol/stepper unipolar (6 terminal). The solenoid has only 2 terminals, I have also added a diode between both terminals on the solenoid side. The solenoid is mounted on the chassis. When I’m switching the ignition on it does make a noise as long as the fuel pump is priming, is it normal? The fuel pump does prime before the engine starts but why is the idle solenoid also doing it? I probably did something wrong, could anyone tell me if I have done any step wrong on my installation? Thanks in advance