Jump to content

GregM

Members
  • Content count

    19
  • Joined

  • Last visited

About GregM

  • Rank
    Member

Profile Information

  • Gender
    Male
  • Location
    New Plymouth, New Zealand

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. GregM

    4g63 boost control.

    Stock Solenoid pin it should be connected to.
  2. For the price of a decent FPR, a Fuel Pump Speed Controller is something I'm considering. No need to upgrade the FPR or fuel return line, and keeps the fuel cooler.
  3. GregM

    Limiting Torque

    Just re-reading your info Adam. I guess I need to work out if Evo rods rail due to tensile failure or compression failure. I'm getting told they fail due to tensile failure now.
  4. GregM

    Limiting Torque

    Thanks, using modeled fuel, so yip. Pretty annoying purposely having to reduce the torque. Tempted to take my chances and not reduce the torque, as I'm only going to max 18psi boost. At peak torque, I'm only at 13psi, so tempting........
  5. GregM

    Limiting Torque

    Thanks Adam, what I'm doing seems to be working right. Abit annoying having to drop the torque down, but so far the engine has held together for a long time by doing that.
  6. GregM

    Limiting Torque

    Hi guys, I'm having a crack at tuning my car myself, its an Evo 5. The block is still stock with 170,000km on the clock. My last tune was on the factory ecu running SD, so have been looking at the logs I did with that and set up of the rom for some guidance. I know what will kill my engine is torque and need to be careful. From the original tune, the timing and boost were limited in the 4000 - 5000rpm range, timing drops and wastegate duty cycle drops, to reduce torque. I've seen comments around where in the rev range the torque kills the engine, and I've seen people say in the mid range, and then others up top. My old tune was limiting in the mid range. I've done a log with wastegate duty cycle and timing not limited in that mid range, and torque was obviously higher. I'm starting to drop timing and boost in that mid range, to match to what my old tuner had, to reduce that torque. As a comparison, my old tune had peak torque at 391Nm at 5900 rpm, and I just had it at 413Nm at 4795rpm. What are peoples view on torque and weak rods. Should torque be limited in that mid range, or is it up top that kills it? I've always been told mid range, like my tuner has tuned it like in the past. It would be good to get some opinions.
  7. GregM

    Subaru knock problem

    I'm learning and setting knock control up myself for the first time on, but on an Evo. If Cylinder 4 is so much higher than the rest, I would have thought you'd turn the gain level on cylinder 4 down, and keep reducing the gain until the knock level all lines up. For those experts, am I on the right track on what should be done in this situation?
  8. I've talked to Simon on this. I was getting an error on DI8, so checked my power feeds which were good. My signal wire looked good, so I changed the DI to DI5 and it worked straight away. Simon said he tried it on the bench this morning and got the same result as me, error when trying to use DI8.
  9. If anyone else comes across this, only my E4-8 ecu I could not use DI8 which is on the XS loom, I ended up using DI5 which worked fine.
  10. GregM

    Remote/email tuning.

    I'm having a go at tuning mine myself and have looked at alot of the HP Academy videos, I haven't played for long and have the fuel pretty good for start, cruise and full power runs off the wastegate. Time to get the knock sensor set up and increase the boost, then add some timing.
  11. GregM

    Knock Setup on G4+ Plug in - EVO 6

    I'm thinking I may attempt to tune my car myself, the only thing that makes me uneasy is setting up the knock sensor. This is a great how to, so will look at giving it a try. It would be great to see what final settings others ended up with, as I am guessing that there will be variances between cars, but not too much?
  12. GregM

    Evo 6 With Link G4

    I can't wait to get mine tuned, booked in for the end of June when finances are better.
  13. GregM

    Windows tablet power from USB?

    I'm a complete novice, so learning as I go. Its the full version of PC link, so you can do everything. The tablet though is too slow for doing anything much more than displaying the dash. I'd want a keyboard and mouse if I was to even try to use it for anything more than a dash. I was thinking of getting a bluetooth keyboard etc to use with it, but don't see the point. If you want to tune, a laptop has the power to do the job properly.
  14. GregM

    Windows tablet power from USB?

    Tablet from Noel Leemings works brilliantly and having 2 USB ports made it so much easier designing my dash layout with a full size keyboard and mouse connected, plus being charged via the DC Port.
  15. GregM

    PCLink layout

    Go into "options", select "units" and then "options" again and change speed to mph
×