Jump to content

Search the Community

Showing results for tags 'linkg4+'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Link
    • G4+
    • G4x
  • General Topics
    • Guest
    • WishList
    • Engine Tuning
    • Customers Vehicles
  • Vi-PEC
    • Vi-PEC i Series
    • ViPEC V Series
    • ViPEC Power Sport
  • Historic Products
    • Link G4
    • Link G2 G3
    • Link G1

Calendars

There are no results to display.

Blogs

  • Bryan
  • 카지노 사이트, 카지노 추천«TSG79.COM
  • 2JZ Tuning Tips

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


ECU model


Serial Number


ECU model

Found 5 results

  1. Hai, Greetings All, i am Dinie From Malaysia. I am new with link ecu. I have a project, honda D16 engine. Recently, i install link civic(95) plugin to the car, do the COP setup. I still use the original distributor as a trigger, do the ignition test and all my coil did the spark. But the car still wont start. I really appreciate all the help.thank you
  2. Hey guys, just got my 3sge beams engine running in my corolla with the Link g4+ monsoon and a harness built by Panic Wire. I'm having some issues with my Link Can-Lambda unit though. There was originally an OBD plug with the power, ground, can H, & can L wires I needed for the 02 in the Panic ECU harness. So I cut the plug out and soldered a new extension to the 4-way deutsch lambda plug. I originally had the wires mixed up due to the wire colors being different than the link pin diagram. Panic uses the universal can-obd wire colors. It is now wired with 12v to the power and 2.4v for both can H & can L. He also said it should be fine that I connect straight to those 4 wires and do not need a relay or capacitor. Now the issue, in the "runtime values" the CAN tab shows all green/ok but in the ECU STATUS the lambda 1 error displays 26 battery under voltage, then 33 open circut APE-IPE, and 16 heated too long. The status goes back and forth from diagnostic to calibration and the temperature back and forth from 32f to 750f or so. AFR always reads 10.08. Voltage is around 13.5v. I also setup the can setting to the link ecu specifications on the site. I will attach a log file showing the info and could use some help with this. Should I wire it differently, was the unit damaged by having the pins mixed up at first, or are there some settings I should change? Any insight would be most appreciated and thanks for reading. lambda error.llg beams.pclr
  3. hey guys! i just finish wiring link atom 2 on this 4age 20v. now im having a problem with the trigger signal, theres no signal on trigger when cranking the engine. Trigger 1 is on NE, Trigger 2 is G2 and ecu gnd is on GND. this is the trigger setup on my laptop, Trigger Mode, Multi-Tooth Trigger Priority, Trig 1 Trigger 1 type Reluctor, level 1, Cam, 24tooth Trigger 2 type reluctor, level 1, sync mode Cam pulse 1x
  4. Hi Guys, Looking for some guidance on what would be the best approach to wire in the Link CAN Lambda unit to an R32 GTR. Should I run an independent relay from the battery to power this unit or is there a way to tap into the factory loom where the ECU plugs in, to provide switched power to this? Cheers. Jed
  5. Ted

    Subaru knock problem

    Hi there after finishing with my tuning with the base maps etc i have tried to fix the knock table. the problem that i am facing is that i am puting my nmbers in the kno ck table and is retarding where i have bigger numbers. i have the log files if anyone can understand why is happening. i am also attaching my map file that i run now on the car I'll be great full if anyone can help me Log 2018-05-8 9;31;12 pm.llg TED WITH KNOCK 08052018.pclr
×
×
  • Create New...