Jump to content
7ishnz

Kawasaki ZZR1400 link install

Recommended Posts

I am using a monsoon ecu on a turbo zzr1400 and have a couple of questions about the setup.

The motor has a 24-2 crank trigger and a cam trigger, both variable reluctance sensors. I have no way of checking the base timing as the trigger is internal. Any ideas how I can resolve this?

The injectors are 330cc but I can’t find any data for them... how should I configure them?

Does anyone have a base map I could use for basic fuel and ignition settings? Maybe from a hayabusa or similar?

Thanks.

Share this post


Link to post
Share on other sites

Couple of H2's on here and another local to me with turbo ZX10 all with Link G4+ 
I am set to 245 deg , so is the zx10,  Andys is similar but -360 from there 
Thought the 14 has the same inspection hole in the alternator cover to check timing with , need an adjustable timing light though .
If no one comes up with more specific maps for the 14 i can send you something that will likely need a lot of tweaking , but should get you running 


 

Share this post


Link to post
Share on other sites

Hi Greg,

Thanks for the info.  If you could send me something to get started with, it would be appreciated.

There is no viewing port on the stator cover on my motor.

 

Share this post


Link to post
Share on other sites

Havent forgotten you 
one of the files i was going to reference is not opening on my current Vipec or G4+ versions and i will run it through an ecu to update it  and adapt a few things to suit your setup 
EG single injectors instead of my staged 
 

Also what coil driver are you planning , if your looking at smart Coil on plug i can leave the R35 coil setup in the mix 

You will need to access the timing to setup properly , can you remove the radiator and give it an alternate coolant supply short term 

Share this post


Link to post
Share on other sites

Hi Greg,  thanks for the reply.

 I have the stock kawasaki coil-on-plug setup.   Stock 330cc injectors ( I think).   

Can't run the engine with the timing cover removed as it is a wet area and I'll get 4 ltrs of oil sprayed around the shed....   Not sure how I am going to sort that out.

Do you know if I can use one of the timers to run the turbo oil scavenge pump through an Aux output?  I need it to run 30secs, off 30 secs then repeat only when the engine is running...

Thanks.

Share this post


Link to post
Share on other sites

Early 14 with the 330 injectors ? , too small for a turbo , you will probably run out of injector before 250hp
 good option is H2 injectors,  650cc at 50 psi and guys are taking them out to replace with 1150's 
What fuel pump and regulator ? 

Stock coils will not work with the Link without a coil driver or coils with internal ignitors  , the file below is setup for smart coils , LS2  (D585) coils with short leeds, 

You will need to calibrate trigger 2  base timing , Shouldn't  loose a heap of oil at once if you remove the cover, or get a sacrificial cover and drill it with something like  25mm  to get a good window at the timing mark and stay mostly dry 

file below should get you going once base timing is set , its from my busa done in traditional fuel mode ,  with the H2 base timing , and 240cc primary injectors (i switched of the staged injectors )so it may be a little rich initially and fuel maps will be way off once you start making a few psi boost , play with the master fuel or master fuel % trim once started to get it running smooth 


you will need to setup and test all your AN inputs and outputs  etc before starting 

zx 14 starter.pclr

Share this post


Link to post
Share on other sites

Thanks Greg.

I have purchased the 4 channel ignition module... didn't know the link wouldn't work with the stock coils!

Bosch 044 fuel pump with Tomei fpr.  I will look at changing the injectors to ID 650 units...only planning on 6 psi max boost.

I will study your map...Cheers.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...