Jump to content
Adturb

PNP Ignition Outputs for wasted to direct spark

Recommended Posts

I'm in the process of converting the stock 4G63 wasted spark coils to direct spark COP setup and appear to have hit a speed bump. I've just gone into the manual and PCLink software and it appears that to run sequential ignition you need to align the output with the firing order (IGN OP 1 to Spark 1, 2 to 2, 3 to 3, 4 to 4, etc)? 

The issue I have is that ignition outputs 3, 4 and 5 on the EvoLink IX PNP are already used for other functions; fuel pump, A/C Fan, and NB heater respectively.

Coincidentally, ignition outputs 6 and 7 are available (both physically unwired) therefore making them ideal to use for a mini loom to control sparks 3 and 4- but I don't believe I can program them for this???

Is this a software limitation (that could be changed in PCLink/ firmware), or is it a hardware limitation of the ECU?  I am reluctant to start moving pins about within the stock ECU plugs, hence the query.

 

Share this post


Link to post
Share on other sites

Hi

It is a firmware limitation. However the ignition and fuel control is so embedded it would not be wise to try to make this an option. As the risk of causing major firmware bugs is far to large.

You will have to do a wire shuffle to allow the use of 4 coils in a sequential fashion.

 

Share this post


Link to post
Share on other sites

Thank you for the reply Simon,

That's what I thought you might say, but worth asking as it would have saved a headache! :-)  

One other query with the Aux outputs (not Ign or Fuel), outputs 8-13 can't be assigned the 'shift light' function, I would assume this is because they don't/ can't provide a PWM output? 

Would it be possible, again via software or firmware revision, to assign any of the 8-13 aux outputs to be activated directly from the shift light settings, but instead of a PWM output, just turn on or off? I have currently got the LED connected to Aux 13 on the expansion harness and although it doesn't ghost (as it did when on Aux Ign 7), I have had to set it as a GP output based on RPM >7200.

To give me the 2 levels I had in the shift light settings I have set the GP output to activate for RPM >7200 OR virtual aux 3, set to RPM >5000 and gear <2.

Share this post


Link to post
Share on other sites

Hi Simon,

As I can't select PWM output on any of these auxiliaries, it is only possible to activate an output by doing the above. As the ECU can be set to limit at different temperatures and in different gears (which is how I have mine set), it would be helpful if there was an option to switch a digital output ON as soon as the ECU applies any RPM limit? I guess it's the same as the traction light option, but for RPM limit.

Not sure if that makes more sense? :-)

 

Share this post


Link to post
Share on other sites

Wow! @nhidinh123 that is EXACTLY what I needed to know, amazing. Do do they ship to the UK too, or is there another discount code? 

Simon, you could be out a job with great replies like that! :blink:

Share this post


Link to post
Share on other sites

At least it wasn't handbags!

On the Di request could you achieve the switching of the AUX bu adding the engine limits to the aux out conditions?

 

Share this post


Link to post
Share on other sites

Hi Simon,

That's EXACTLY what I needed, thank you :D

I's also noticed that Aux Outputs 1 to 9 that have option to apply a label, 11 to 16 don't come up with that choice? One last dumb question on Aux Outputs, is there no way to change the firmware to add a low frequency PWM (i.e. <20Hz) option to these outputs too?

Big thank you again for the replies B)

Share this post


Link to post
Share on other sites

The label issue will be sorted in a future PC link release.

Ill ask about the low frequency option. I'm suspect it will be a no go as it a hardware limitation of the Micro.

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...