Jump to content
jimbo

1ZZ Smart coils on 2JZGTE (G4+storm)

Recommended Posts

Have a car in with G4+ Storm, 3 channel igniter + bosch coilpack leads.

Wanting to clean the install up as owner going with new plenum and general tidy up.

Can the Storm control 1zz smart Coils (90919-02239) wasted, or at least run Wasted with a COP such as the 3UZ (90919-02230) (built in igniter)

Any other ideas?

 

 

 

 

IMG_6810.JPG

Share this post


Link to post
Share on other sites

Smart Coils are a 5V TTL trigger, so not sure if G4+ Storm has a TTL ignition out and if it does can it drive 2 Smart COPS per channel.

I could build an external Driver board for TTL using 2N2700's driven by the G4+ but do not want to go down that road.

So other option is dumb coils like the (90919-02230) in Wasted

 

Just wondering what others have done

Share this post


Link to post
Share on other sites

Lq9 chevy coils are getting pretty popular on the jz motors.

I'm running Toyota sienna coils on my 1uz with no issues.  very similar to the 3uz coils.

but I don't think that the 1zz coils are smart.  I just think that they are internal ignitor and similar to the rest of the typical Toyota coils.

 

http://www.sq-engineering.com/tech-articles/coilpack-info-guide

Share this post


Link to post
Share on other sites

Lq9 chevy coils are getting pretty popular on the jz motors.

I'm running Toyota sienna coils on my 1uz with no issues.  very similar to the 3uz coils.

but I don't think that the 1zz coils are smart.  I just think that they are internal ignitor and similar to the rest of the typical Toyota coils.

 

http://www.sq-engineering.com/tech-articles/coilpack-info-guide

yeah brad bit from any research the 1zz and 2zz coils are smart type and are 5V TLL driven from most other ECU's

GND = Ground - BROWN
IGT = Trigger Signal (+5V) - DIFFERENT COLOR FOR EACH COIL
IGF = Spark event confirmation (leave it not connected) - BLUE
+12V - BLACK

 

unfortunately its the only one thats sits well on the JZ head.

 

are you running the 90919-A2007 Sienna coil?? and are they performing well in wasted spark??

 

 

Share this post


Link to post
Share on other sites

The link will drive the 1zz &1nz coils fine, you can wire 2 per channel, direct to ecu.  I have used these many times.

If you're buying new, ensure they are genuine denso/toyota as at least here in NZ there are a lot of very nasty Chinese copies about. I had some come to me that sent a high voltage spike back out the trigger wire with every spark event.

Share this post


Link to post
Share on other sites

Yes, it will drive them just fine.  I had the same on my 2J. 

They will do 600hp ATW no problems, this is with 1zz coils in waste spark with a T51R, BP98 pump fuel:

josh_dyno.jpg

Edited by JMP

Share this post


Link to post
Share on other sites

Thanks for that JMP

 

On the 1ZZ coils are you running Falling Edge as spark trigger

and this is the Dwell times I have so far

8V 6.3 ms
9V 5.3 ms
10V 4.4 ms
11V 3.8 ms
12V 3.2 ms
13V 2.7 ms
14V 2.4 ms
15V 2.2 ms

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...