Jump to content

[UPDATE] PCLink 5.6.6.3564 (on hold)


Recommended Posts

G4+ firmware 5.6.6 at RX7S7 plugin have problem

I tried yesterday to My FD.

At first The REoil pump rang tightly.(IGN ON)

I tried RE Oilpump Test Mode (Full Open and Full close)

Then the degree of opening became unstable

The same symptoms were observed even if the pump was replaced.

The stepping motor does not work well.

That's it, I switched it back to the old firmware.

 

I will report it just in case.

Link to post
Share on other sites
  • Replies 103
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

Hey everyone,  I know you've been hanging out for this one. PCLink Version 5.6.6 3564 (DLL rev 3544) 15/08/2018 New Features Right Mouse Click on a time plot to add a marker or sect

You are fine.  For those that do have problems it is very obvious, ecu will be disabled/locked and engine wont run.

Yes it is now ok to run the current release.

Posted Images

7 hours ago, Takshit said:

G4+ firmware 5.6.6 at RX7S7 plugin have problem

I tried yesterday to My FD.

At first The REoil pump rang tightly.(IGN ON)

I tried RE Oilpump Test Mode (Full Open and Full close)

Then the degree of opening became unstable

The same symptoms were observed even if the pump was replaced.

The stepping motor does not work well.

That's it, I switched it back to the old firmware.

 

I will report it just in case.

What firmware was in your ECU prior to the change?  There have been no known changes to rotary oil pump control for many releases but it is possible if you were on something older than 5.6.5 you might have got hit by the corruption thing that Simon mentions above.  Try again once we release the fixed version (hopefully in a few days).

Link to post
Share on other sites

 

1 hour ago, Adamw said:

What firmware was in your ECU prior to the change?  There have been no known changes to rotary oil pump control for many releases but it is possible if you were on something older than 5.6.5 you might have got hit by the corruption thing that Simon mentions above.  Try again once we release the fixed version (hopefully in a few days).

I used before 5.6.6 and now is 5.6.5.3338 firmware.

I will try fixed version. :-)

Link to post
Share on other sites
37 minutes ago, claudiumxg said:

Which version has now the 4g15 triggers in? and where can it be downloaded to test it , because on pc link downloads is still 565.388

It is in 5.6.6.  As per Simons post above we have pulled it off the website temporarily as we have found a problem when connecting to old firmwares.  I expect it will be fixed and re-released in the next few days.

Link to post
Share on other sites
5 hours ago, DOLFO said:

I had FW 5.6.5 updated to 5.6.6 till now no problems. I have a race next week should I downgrade it back to 5.6.5 or I can keep 5.6.6? thanks

You are fine.  For those that do have problems it is very obvious, ecu will be disabled/locked and engine wont run.

Link to post
Share on other sites
On 8/31/2018 at 1:37 AM, Adamw said:

You are fine.  For those that do have problems it is very obvious, ecu will be disabled/locked and engine wont run.

Thanks .......  I have done two ECU's and both work just fine.

Link to post
Share on other sites
12 hours ago, flipski said:

FYI, in future release, could you please update the basemaps for nissan 350z IAT fuel trim table. Sorry if I posted in wrong thread.

image.png.44973925e074ddfc7e5350760405bc7a.png

Im pretty sure that map was done by High Performance Academy, I assume since it is a NA car and wouldnt normally have running intake temps above about 30°C, the enrichment at high intake temps is done intentionally to compensate for hot start heat soak.  

Link to post
Share on other sites
3 hours ago, Adamw said:

Im pretty sure that map was done by High Performance Academy, I assume since it is a NA car and wouldnt normally have running intake temps above about 30°C, the enrichment at high intake temps is done intentionally to compensate for hot start heat soak.  

Thanks for the feedback. I guess this should be part of another thread. 

Link to post
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
52 minutes ago, STY said:

Guys, can you update the Pin Function for Tacho in the Help Manual and default for Base Map on WRXLink 7-9 
its incorrect, should be IGN5 for Tacho not AUX4 (later HW revisions?)

Yep thats been done in 5.6.6.  The manuals on the respective ECU page on our website should always have the most up to date pinouts.  The base map that we send out in the ECU should be set up correct as far as I know, are you saying its not? 

Link to post
Share on other sites
1 hour ago, STY said:

Unless its only been updated in 5.6.6 (i had to revert to 5.6.5:3338) my base maps are still showing AUX4 -Tacho 
for: Subaru WRX V7 G4+ Xtreme Plugin.pclr with a date of 24/08/2016 

The ECUs are being shipped out with the correct map already loaded in them.  The 5.6.5 basemap is set up wrong as that was from before the hardware change.  Yes all the basemaps have all been updated in 5.6.6 to cover hardware changes, firmware changes and a few mistakes that have been reported.

Link to post
Share on other sites
  • Simon unpinned and locked this topic
Guest
This topic is now closed to further replies.

×
×
  • Create New...