sbn1979 Posted February 20, 2019 Report Share Posted February 20, 2019 Anyone have a wiring diagram for this? Thanks Will be based on an Evo x Tb and pedal Quote Link to comment Share on other sites More sharing options...
Simon Posted February 20, 2019 Report Share Posted February 20, 2019 We have a pinout for the EVO 10 throttle in the PC link help file Navigation: Wiring Information > Output Wiring > E-Throttle > Specific E-Throttle Applications > Mitsubishi EVO X We don't have anything on the pedal. sbn1979 1 Quote Link to comment Share on other sites More sharing options...
goddess7 Posted February 21, 2019 Report Share Posted February 21, 2019 (edited) Here is evo10 APS. pin1 : +5V pin2: Sensor Ground pin3 : APS (Main) pin4 : +5V pin5 : Sensor Ground pin6 : APS (Sub) Edited February 21, 2019 by goddess7 Simon 1 Quote Link to comment Share on other sites More sharing options...
sbn1979 Posted February 25, 2019 Author Report Share Posted February 25, 2019 Missing aux10 for motor dbw??? Quote Link to comment Share on other sites More sharing options...
ClintBHP Posted February 25, 2019 Report Share Posted February 25, 2019 Aux9 in the software controls Aux 10 - conversely Aux4 controls Aux 9 sbn1979 1 Quote Link to comment Share on other sites More sharing options...
sbn1979 Posted February 26, 2019 Author Report Share Posted February 26, 2019 Thanks for clearing that up, should aux 9 be pinned to motor +or-? Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 26, 2019 Report Share Posted February 26, 2019 The physical Aux 9 output should be connected to the Motor + as per the help file Simon pointed out above. In the software set Aux 4 to "E-Throttle Signal 1" and set Aux 9 to "E-throttle Signal 2". sbn1979 1 Quote Link to comment Share on other sites More sharing options...
sbn1979 Posted February 26, 2019 Author Report Share Posted February 26, 2019 And throttle motor -ve to aux 4? can I use a virtual aux 1 for throttle relay? Quote Link to comment Share on other sites More sharing options...
sbn1979 Posted February 28, 2019 Author Report Share Posted February 28, 2019 Ok so everything works however I cannot run the car at this time but the pedal is not moving the throttle is there a rpm lockout I’m missing somewhere? The pedal and throttle have calibrated fine now btw Quote Link to comment Share on other sites More sharing options...
EvilEvolution8 Posted February 28, 2019 Report Share Posted February 28, 2019 I think you have selected "Quite Mode" in the dbw configuration... Pedal dont move the throttle when engine is not running...pedal will move the throttle only when engine is running. Quote Link to comment Share on other sites More sharing options...
cj Posted March 1, 2019 Report Share Posted March 1, 2019 6 hours ago, EvilEvolution8 said: Pedal dont move the throttle when engine is not running. this is true by default and is probably right. You can change it through from Quiet Throttle to "run throttle" in ethrottle setup screen. Then it will move any time the key is on Quote Link to comment Share on other sites More sharing options...
sbn1979 Posted March 1, 2019 Author Report Share Posted March 1, 2019 That’s the weird thing I’ve tried in both modes and nothing but everything seems to work Quote Link to comment Share on other sites More sharing options...
Adamw Posted March 1, 2019 Report Share Posted March 1, 2019 So did it run through the TP calibration procedure ok? Can you do a short PC log with a few pedal presses and attach that and your tune file here. Make sure to set the "when stalled" setting to run throttle when you do the log. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.