Jump to content

suby3.0

Members
  • Posts

    26
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

suby3.0's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. suby3.0

    EZ30R tuning

    Thank you I will try all that and let you know.
  2. suby3.0

    EZ30R tuning

    Thanks, I will change or fix my alternator.
  3. suby3.0

    EZ30R tuning

    That is not my battery but alternator. what is the maximum? 14V? I need to add a regulator?
  4. suby3.0

    EZ30R tuning

    HI Adamw I was finally able to run the car after a fuel pump issue. See in attach file. I have error with TPS I calibrate the TPS. But I get 100% when not using than go to 0 when I accelerate a bit to 98% full open. The thing I put a bigger cable drive throttle body. I believe the original size was 72mm I put a 90mm with a reducer adaptor. But I think when I'm open 70% I have the maximum air flow. I don't know if this is important for fuel mix. The other problem I don't know how to set up the Lambda in the software to work. And I get a lot of RPM restriction because the faults. I wasn't able to get Brad Burnett to answer me. Thank you for your help. best regards run test 3282021.llg
  5. suby3.0

    EZ30R tuning

    Hi Brad, Can you give me your contact or text me at 772.360.9245 Laurent
  6. suby3.0

    EZ30R tuning

    Hi Brad, Can you tell me more about your business. Do you have a awd dyno? I can bring you the my car to see if you can help me to make it works right. I'm in Vero Beach just an hour from you. Regards Laurent cell: 772.360.9245
  7. suby3.0

    EZ30R tuning

    Hi I put a EZ30R 2006 in my GC8 with a ECU Fury. The engine run ok now after first tuning. Not having mush torque. I'm not sure that my AVCS are set up or map right. it is very hard to find a good tuner in Florida who know G4+ well. I will need some advise. if somebody can look at my tuning. Questions: 1-Trigger 2 vtt left have has a offset 70.0 ATDC and DI 2 for right VTT has a offset 190.0 ATDC it is correct or not? 2-do the VTT map is correct? 3-Aux out 1 avcs (I read some where need to be 300HZ) mine are set at 250Hz? 4-Do DI7 and DI8 are set correctly. I wasn't able to get a reading from DI8. 5-VTT set up and table 1 are they correct? see file attached. Thank you in advance Laurent EZ30R-5 fury 2021.pclr
  8. suby3.0

    Fury for EZ30R

    Hi, I do not need to ground Inj8 to power the ecu. I'm using DI3 with the ignition switch and a diode to the ECU 12v. But INJ 8 do not connect to the ground when ecu on even it show inj8 on and green. see ignition test in attachment. I have to go and switch INJ8 from low polarity to high polarity than low again to connect inj8 to ground. Kind of forcing it. ignition test.llg
  9. suby3.0

    Fury for EZ30R

    Hi, see ECU wiring in attachment. The ECU power up when ignition is on. AF8 ( aux Inj 8 is on on the screen set the polarity to Low) but the relay don't start. I can start them by switching the polarity to High than Low again and it will work or connect AF8 to ground. I have an other problem too . My AN3 TP9Main) has a voltage from 0.06 to 4.00 when engine off. When the engine start at idle with out touching the accelerator the voltage change to 14.6 and try to accelerate the engine die. Suby ECU wiring.pdf
  10. suby3.0

    Fury for EZ30R

    I check everything. The problem is that Inj 8 set has ECU power holder need to connect to the ground when ECU is power to initiate the relay on. But it doesn't. Can you explain how INJ 8 works in the ECU when set has ECU power holder? I'm able to turn the relay on by connecting a wire to Inj 8 to the ground after the ECU is powered by ignition switch.
  11. suby3.0

    Fury for EZ30R

    Hi, The engine run Thank you. both DI3 and Aux Fuel 8 are on but the main relay and the holder relay don't click. I will check voltage on all connection this week end. but do aux fuel 8 set at ecu power holder is on that mean the connection is connect to the ground set on low? I can make them click using the labtop switching from high to low at this time it work. but turn ignition off than back on nothing.
  12. suby3.0

    Fury for EZ30R

    The injector are OEM 16611AA700 brown. or 297-0010 Denso. Cannot find the cc/min but need to be close of 297cc linkecu4.4.pclr
  13. suby3.0

    Fury for EZ30R

    Sound like the engine want to start but the still something off like to much fuel. Trigger Scope Log 2020-05-20 6;13;02 pm.llg crant test 4.llg I have an other small problem. see drawing attached that is my wiring for the hold power to the ecu because the ISC I'm using. I set up thee ICS to turn key off 3s and that work when I turn it off. But to turn it on that where I have a problem. I set up aux fuel 8 to hold power to Ecu with LOW input. But he doesn't control the relay until with the laptop I put on High then low again wit ignition switch on and at the time the main relay click. But if I turn off even I download to the ECU this parameters I have the same problem. Can it be the set up of DI3? IMG_0398.HEIC
  14. suby3.0

    Fury for EZ30R

    Hi, I fix DI3 and did the test. The engine first try to start some cylinder was firing but stop brutally and power shut down from ECU and got disconnect. That was crank test 2. After I did trigger scope test than try again with crank 3 they was some puffing but that's it. crank test 2.llg crank test 3.llg Trigger Scope Log 2020-05-20 7;55;15 am.llg
  15. suby3.0

    Fury for EZ30R

    see the files attaches map and logging of crancking. Thank you for your help linkecu4.4.pclr log file starter.llg
×
×
  • Create New...