Hi All,
I have recently bought a Links Thunder ECU and after going through the wiring information I have assigned my pin Inputs and Outputs. If someone could look over the attachment of my wiring to make sure I have done it correctly or if I have missed something I would appreciate your time before I start wiring.
Secondly, I am looking for a base map so I am able to start it and check it over before taking it in for a tune on the dyno.
The engine is a Toyota 4AGE 20V Turbo. (I have removed the Dizzy and now have Hall sensors for the Crank and Sync)
Thank you for taking the time to have a look.
Regards
Gavin
Wire Description
Pin #
Installer Connection
Typical Application
Trigger 1
A8
Crank Angle Sensor
Trigger 2
A9
Cam Angle Sensor
Analogue Temp Input 1
A15
Engine Temp
Analogue Temp Input 2
A16
Intake Temp
Analogue Temp Input 3
B6
Fuel Temp
Analogue Temp Input 4
B7
Transmission Temperature
Analogue Volt 1
A17
External Map (Intake)
Analogue Volt 2
A22
External Map (Exhaust)
Analogue Volt 3
A33
TPS (Main) E-throttle Body (TPS)
Analogue Volt 4
A14
(Sub) E-throttle Body (TPS)
Analogue Volt 5
B33
Accelerator Pedal (Main) (FPS)
Analogue Volt 6
B15
Accelerator Pedal (Sub) (FPS)
Analogue Volt 7
B16
Fuel Pressure
Analogue Volt 8
B23
Engine Oil Pressure
Analogue Volt 9
Analogue Volt 10
Analogue Volt 11
Analogue Volt 12
Analogue Volt 13
Analogue Volt 14
Analogue Volt 15
Analogue Volt 16
+5V Out
A32
TPS and MAP sensor power
+8V Out
A6
Cam/Crank angle sensor power supply
Ignition 1
A13
Cylinder 1 (Toyota 1NZ cop)
Ignition 2
A12
Cylinder 2 (Toyota 1NZ cop)
Ignition 3
A11
Cylinder 3 (Toyota 1NZ cop)
Ignition 4
A10
Cylinder 4 (Toyota 1NZ cop)
Ignition 5
Ignition 6
Ignition 7
Ignition 8
Injection 1
A4
Cylinder 1 (Bosch 2000 ID)
Injection 2
A3
Cylinder 2 (Bosch 2000 ID)
Injection 3
A2
Cylinder 3 (Bosch 2000 ID)
Injection 4
A1
Cylinder 4 (Bosch 2000 ID)
Injection 5
Injection 6
Injection 7
Injection 8
Auxiliary Output 1
A21
VVT Control
Auxiliary Output 2
A20
Fuel Pump 1
Auxiliary Output 3
A19
Fuel Pump 2
Auxiliary Output 4
A18
Thermo Fan 1
Auxiliary Output 5
A29
Thermo Fan 2
Auxiliary Output 6
A28
Intercooler Pump
Auxiliary Output 7
A27
Boost Solenoid
Auxiliary Output 8
A26
Transmission Thermo Fan
Auxiliary Output 9
B18
(E-throttle Motor +)
Auxiliary Output 10
B26
(E-throttle Motor -)
Auxiliary Output 11
Auxiliary Output 12
D15
Trans Brake Solenoid
Auxiliary Output 13
D16
Gear Shifter Solenoid (Shiftnoid)
Auxiliary Output 14
Auxiliary Output 15
Auxiliary Output 16
Auxiliary Output 17
E-throttle Motor 2
Auxiliary Output 18
E-throttle Motor 2
Auxiliary Output 19
Auxiliary Output 20
D3
Tachometer
Knock 1
B9
Knock Sensor
Knock 2
Digital Input 1
A30
Rear Wheel Speed Sensor
Digital Input 2
A31
Trans Brake Button
Digital Input 3
A23
Bump Button
Digital Input 4
B21
Flex Fuel Sensor
Digital Input 5
B20
12 Position Launch Dial
Digital Input 6
B19
Launch Control Button
Digital Input 7
B30
Front Wheel Speed Sensor
Digital Input 8
B29
Boost Control Dial
Digital Input 9
Digital Input 10
Digital Input 11
Turbo Wheel Speed Sensor (No clue where to put the signal from the Garrett turbo speed sensor)
Digital Input 12
Digital Input 13
Digital Input 14
Digital Input 15
Digital Input 16
MES 1
C3
Sensor Green Wire (pin 5)
RE 1
C6
Sensor Black Wire (pin 6)
Heater 1
C7
Sensor White Wire (pin 3)
IPE 1
C5
Sensor Yellow Wire (pin 2)
APE 1
C4
Sensor Red Wire (pin 1)
MES 2
Sensor Green Wire (pin 5)
RE 2
Sensor Black Wire (pin 6)
Heater 2
Sensor White Wire (pin 3)
IPE 2
Sensor Yellow Wire (pin 2)
APE 2
Sensor Red Wire (pin 1)
Main Relay +
Main Relay -
Ignition Switch
Thermocouple 1
Thermocouple 2
CAN 1
EGT CAN
CAN 2