maccakpa

after i change wall wetting to zero flooding problem went away and even idle becomes natural. Thanks to you guys! About SPWA is I just downloaded it from Injectordynamic site. but the tricky thing is they have 2 datas for id1700 injectors

thank you for your feedback Adam, the main problem is cold start issue. Car drives okey while cruising. Cold or warm start ups are most likely too rich. and i do only have 1 chance to start car with wide open throttle. Otherwise car goes too rich and doesnt start up

Hi guys. my car (forester sti JDM) was tuned on id1050x and 272 camshafts before. now i changed ID1700x injectors kelford 282 in out camshafts with 1mm oversized valves walbro 525 lph fuel pump HKS m45iL sparks. The problem is cold start and after cruise idle is terrible. Could you guys please have a look at my log? idle unstable.llgx tuned 1.5 bar 98 octane.pclx idle warmup 2.llgx

hello again. solved car idle control and car shuts down in traffic issue. today i made 3th and 4th gear pull using 95 octane fuel +50/50 water methanol injection. While run there is huge knock accurs on cylender 2. is there anyway to solve this issue?/there is something with heads slapping that area since after i got my iag900 blongblock heard with headseat im sure it was not piston slap/ please see attached file and log. 3rd and 4th gear log with file

thank you sir! and i still have a problem. 1. Cold start its still little bit of slow start. 2. when i let off the throttle car shuts down in a cruise range and after WOT 3. when i tried to park (turning steering wheel) car shuts down either. what should i do? I zeroed warmup enrichment 80-110ECT to all "0"

I did couple pulls on 3rd gear and cruise logs added to google drive as well

thank you for your support ! i uploaded map and now idle is smooth . here is the log https://drive.google.com/drive/folders/1q3Gc6elVBxZp11lIBIFbOdjh3KS5vixD?usp=sharing

Hello guys! Need some help on cold start and idle Last few months Im keep trying to figure out smooth idle and correct idle. Since i have like no pro tuner in my country. Car drives okey in cruise and couple of WOT. The problems are: 1. On cold start car doesnt hold its rpm and shuts down 2. Cranking time is longer (about 3 secs or more) 3 Idle is unstable rpm rises and falls almost constantly. Mods are: -IAG900 longblock -Kelford 282 cams with 1mm oversized valve (with all supporting mods and ported) -Precision gen 2 6266 v band 0.82 hotside turbo - 38mm tial WG - 45mm TIAL BOV - ID1050x top feed injectors (have id1700x since im not sure fuel pump could hangle it) - Aeromotive A1000 FPR - 340lph fuel pump - 10 bar fuel pressure gauge (Calibrated) - 5.2 bar map sensor (Calibrated) - GM IAT sensor - MAC 3 port boost solenoid - AEM water/meth injection if anyone could help me with happy idle i would be so happy https://drive.google.com/drive/folders/1kCOBWtsmGkheDbQia-t6jeAFpD4GvWR4?usp=sharing

finally start my car. can someone please look at my log and file? Problem is: -Cant hit target idle rpm -little boggy from 800 rpm to 1500rpm -cold start is kind of lean for like 20 second or so. Car mods are: -iag1000+ longblock (kelford 282 camshafts) -precision 6266 turbo -id1050x fuel injectors -AEM wideband sensor -HKS M40iL sparks OEM map sensor, OEM FPR, OEM fuel rails.

got it fixed it with run throttle.

yesterday i tried again. and when i start the car TPS was working for couple of sec then stopped working. due to error voltage maxed or something. i couldnt do a log at that time. If its possible do you guys have a AJ542 ecu pinout? couldnt find it online. Here i attached last map. with throttle.pclx

when i change to AN volt 2 & 3 tps display was not showing any movement.

Hello guys ! i have purchased this ecu for my 2007 jdm forester sti. It has DBW, single avcs,and ej257 and almost same as USDM 2007 wrx. anyways, car started kind of idles but with no throttle response. changed e-throttle setup and its no go. please have a look on my file and log FORESTER SG9 START LOG NO THROTTLE.llgx no tps last 2.pclx

jzx100-modelled-sard-850cc 1.pclx hello again guys, im still struggling to dial in injectors. could you guys please inspect my map? connected AEM FPS 150psi AEM wideband sensor IAT sensor

im just curious when i change fuel type to modelled and change the injector to 850 and attach injector data car doesnt start.