Jump to content

Rossogy

Members
  • Posts

    24
  • Joined

  • Last visited

Recent Profile Visitors

145 profile views

Rossogy's Achievements

  1. Hi Adam, attached logs with filter level 3 & then filter level 1. Let me know what you think. Cheers 5000rpm.llg 6000rpm.llg 5000rpm filter 1.llg 6000rmp filter 1.llg
  2. Hi guys, Just off the dyno with a mates car and we are having bad trigger issues so im looking for advice. We have changes both crank & cam wires to shielded wires & checked all earth points. this all made it alot better but there is still something holding us back from reaching our rpm limiter. i will attach my tune & Log for advice. you will see the weird spike in rpm reaching 11-12000 rpm. Any advice on where to go from here would be appreciated. We have ordered a new crank trigger wheel which is our next port of call. Thanks guys. 1.5JZ trigger issue.pclr callum trigger issue 6600.llg
  3. Rossogy

    Can lambda help

    Hi guys. Having an issue with can lambda I keep getting errors. 16 heated to long 33- open circuit RE-IPE replaced the sensor but it’s still the same. any ideas?
  4. No, connection still active. And internal resistor is enabled. if I disable in pc link the dash powers up as normal.
  5. Yes can lambda on Can2 on the B connector & dash is on Can1 on the round connector ill get some pictures when I’m next with the car Thanks again Adam
  6. Hi Guys, Currently working on a project where im connecting an AIM MXS 1.2 Strada dash to a G4+ Xtreme. Now im having issues where its not displaying at all and im getting errors. if i activate the 120ohm resistor in the dash doesnt go past the load screen. All wiring has been double & triple checked and is fine. heres my file and my RS3 file Thanks in advance for the help Cheers Ross MXS 1.2 Strada G4+ Xtreme2.zconfig Canbus setup.pclr
  7. Rossogy

    E36 pnp no start

    Have you tried using the Trigger Scope function? It will let you know if its seeing anything
  8. Rossogy

    E36 pnp no start

    are you using the OBD1 Crank sensor?
  9. Worked perfectly Adam thanks for that!
  10. Thanks Adam ill give that a try and report back
  11. Hi guys, Looking for some experenced help with e throttle setup as this is my first experience. Im using a 350z dbw throttle & Bmw E46 pedal. Its all working fine in setup mode but once i set it to ON im having issues with TP/Targer accumulator I have tried copying the PID settings from the Link 350z base file but it send the throttle plate crazy. i will attach my file & Log Thanks Ross 2JZGE+T DBW 21-2-21.pclr 2JZGE vvti.llg
  12. Hi Adam, continuity all tested ok..
  13. Hi Adam Pic shows white- Can H wired to B loom can2H green- Can L wired to b loom can2L wires are twisted to the dash also as requested if it’s over a distance
  14. Adam, Just changed all that you requested and its still the same. Any other ideas? I noticed in the runtime values that there are errors on CAN2 like you said. I double checked the wiring again and it is 100% correct Thanks for the help Ross MXS 1.2 Strada G4+ Xtreme2.zconfig 2JZGE+T VVTi Dash canbus2.pclr
  15. Ive already tried changing between the three choices.. i had an issue with my older style Atom ecu and i had to add in a resistor on the ecu side. it was one of the early metal case G4+ Just looked back through my old config for the Atom and it was using the LINK - CAN_BUS_BASE_LCC (VER. 02.00.02)
×
×
  • Create New...