Rossogy
Members-
Posts
24 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by Rossogy
-
Hi Adam, attached logs with filter level 3 & then filter level 1. Let me know what you think. Cheers 5000rpm.llg 6000rpm.llg 5000rpm filter 1.llg 6000rmp filter 1.llg
-
Hi guys, Just off the dyno with a mates car and we are having bad trigger issues so im looking for advice. We have changes both crank & cam wires to shielded wires & checked all earth points. this all made it alot better but there is still something holding us back from reaching our rpm limiter. i will attach my tune & Log for advice. you will see the weird spike in rpm reaching 11-12000 rpm. Any advice on where to go from here would be appreciated. We have ordered a new crank trigger wheel which is our next port of call. Thanks guys. 1.5JZ trigger issue.pclr callum trigger issue 6600.llg
-
Hi guys. Having an issue with can lambda I keep getting errors. 16 heated to long 33- open circuit RE-IPE replaced the sensor but it’s still the same. any ideas?
-
No, connection still active. And internal resistor is enabled. if I disable in pc link the dash powers up as normal.
-
Yes can lambda on Can2 on the B connector & dash is on Can1 on the round connector ill get some pictures when I’m next with the car Thanks again Adam
-
Hi Guys, Currently working on a project where im connecting an AIM MXS 1.2 Strada dash to a G4+ Xtreme. Now im having issues where its not displaying at all and im getting errors. if i activate the 120ohm resistor in the dash doesnt go past the load screen. All wiring has been double & triple checked and is fine. heres my file and my RS3 file Thanks in advance for the help Cheers Ross MXS 1.2 Strada G4+ Xtreme2.zconfig Canbus setup.pclr
-
Have you tried using the Trigger Scope function? It will let you know if its seeing anything
-
are you using the OBD1 Crank sensor?
-
Worked perfectly Adam thanks for that!
-
Thanks Adam ill give that a try and report back
-
Hi guys, Looking for some experenced help with e throttle setup as this is my first experience. Im using a 350z dbw throttle & Bmw E46 pedal. Its all working fine in setup mode but once i set it to ON im having issues with TP/Targer accumulator I have tried copying the PID settings from the Link 350z base file but it send the throttle plate crazy. i will attach my file & Log Thanks Ross 2JZGE+T DBW 21-2-21.pclr 2JZGE vvti.llg
-
Hi Adam, continuity all tested ok..
-
Hi Adam Pic shows white- Can H wired to B loom can2H green- Can L wired to b loom can2L wires are twisted to the dash also as requested if it’s over a distance
-
Adam, Just changed all that you requested and its still the same. Any other ideas? I noticed in the runtime values that there are errors on CAN2 like you said. I double checked the wiring again and it is 100% correct Thanks for the help Ross MXS 1.2 Strada G4+ Xtreme2.zconfig 2JZGE+T VVTi Dash canbus2.pclr
-
Ive already tried changing between the three choices.. i had an issue with my older style Atom ecu and i had to add in a resistor on the ecu side. it was one of the early metal case G4+ Just looked back through my old config for the Atom and it was using the LINK - CAN_BUS_BASE_LCC (VER. 02.00.02)
-
Ecu map & Dash config attached 2JZGE+T VVTi Dash canbus.pclr MXS 1.2 Strada G4+ Xtreme.zconfig
-
Hi Adam, so just had a check.. DI9&10 are off and I’ve updated all firmware (ecu & dash) double checked I had the can wires the right way round. Still no communication to dash... any idea? I’ll upload my config and file once I’m home also. Thanks Ross
-
Thanks Adam, I'll Double check the firmware & DI9 & 10 today I will report back Thanks
-
Hi Guys, Does the above ecu have a built in 120ohm resistor for Can termination? I have the Link (Aim) MXS Strada dash and it wont show data so im guessing i either need to activate the resistor in PCLink or i need to add a resistor in.. Any help is appreciated Thanks Ross
-
Thanks Adam, All up and running now.
-
Hi Guys, Does anyone have a pinout for the 350z throttle body? im connecting it to my G4+ Xtreme and cant find any solid information. also i will be using a bmw e46 pedal if anyone has a pinout for that also. Thanks
-
Thanks for that Adam. ill have a look at the sensor pinouts from my previous setup and see what its like. Cheers!
-
Hi guys, Currently making my loom to run my 2JZGE+T VVTi with G4+ Xtreme and i have a couple of questions. When wiring up the VVTi Solenoid will i need a flyback diode? and does anyone know the correct pinout? Does anyone know the correct pin on the cam & crank for signal? Will i need a flyback on the Mac valve also? Any help appreciated! Cheers Ross
-
Hi guys, I’m having a small issue, I have recently changed my wideband controller due to my innovate one giving up. I have calibrated the new one using Cal6 and it’s all working fine. The only problem I’m having is that the runtime values for Lambda 1 are not the same as the actual lambda readings. Now this wouldnt usually bother me but me but I have the link MXS dash and that shows the runtime value not the actual lambda reading... so as you can imagine it’s all over the place. I have attached a small video (hopefully it works!) 8F369CEC-ABF2-4233-BE08-621D9BE39A07.MOV Anyone any advice on how to sort this? Thanks Ross