cHeMiCaL_

Hi, I am upgrading my G4+ Fury to Fury X. Is there any automation apps to convert my G4+ (PCLR) maps to the latest generation X (PCLX)? It's very difficult to do it manually. thank you.

Appreciate it so much, @Adamw!! Thanks again @Vaughan!

Thanks much @Vaughan! but i need rather larger 140 bar / 2030psi calibration table. Hopefully i can achieve the rated accuracy from it.

Hello all, need some advise, I'm setting up clutch and brake pressure sensors using linkecu press sensor part no 101-0186. Currently in PCLink G4+, there is no selection for the sensor's calibration in the drop-down menu. Does anybody has calibration table that i can refer to? Thanks much! cheers!

Noted with thanks @Adamw! Speed sensor works fine as i can see it through my MXP dash all this while. Let me diagnose everything again. much thanks for all of the advices! cheers!

ok @Adamw i will retry again when the situation permits. My driven LF wheel speed source is assigned and working well. for the gear ratio calc reported in first gear is 655.35

Yes adam, ive read through and followed all the instructions in the manual. I’ve not been lucky with my ecu and been getting loads of issues since beginning. I still hv warranty ticket open btw and hvnt got the chance to this return to your warranty team. the problem i hve now, even before i can get up to 15km/h, it will report ‘finished’, where it should be reporting unsuccessful. Whether it’s 15km/h or 0km/h it will report ‘finish’ after 3 seconds of running and i will get status gear ‘1’ and thats abt it. I hope my explanation gives better picture on my current situation. Much thanks! thanks Vaughan, will take that as a consideration surely!

Hi @Adamw, Need your assistance, Am using G4+ Fury and i cant get my gear detection to work. When i initiate the gear calibration (through ECU Calculated), the Gear Ratio Status' "Calculating Gear" will always display "Finished" after 3 seconds even though i am not moving. This problem applies to all 5 gears. Can you please help to manually enter my gear ratio as per below? currently its full lockdown in my hometown, so i cant go out for a drive to do logging for you. I have also attached my config files for your perusal. 1st Gear (2.875) 2nd Gear (1.950) 3rd Gear (1.444) 4th Gear (1.096) 5th Gear (0.825) Reverse (3.416) Final Ratio (4.111) Circumference: 2052.09 mm hear from you and many thanks kindly for your help, @Adamw! cHeMiCaL_ 01Jun2021.pclr

the temp increase when i run the engine but they only increas upto around 33°C. is there anyway i can calibrate inside the linkecu itself? thanks for helping @Adamw!

Yes, they’re reading the same. I have replaced the EGT sensors twice yet still reading the same.

Hi @Adamw! Happy new year! Need help with my Ecumaster EGT to CAN with my G4+ Fury setup. After following all the instructions and setting up the can stream to the letter, my EGT reading for 5 sensors seems to be wrong (too low). Any way you can advise and help me out? screen capture for your perusal as per-below! thanks @Adamw!

thank you @Adamw!!!!

Hi @Adamw, sorry to trouble you again. I have a total of 5 EGT. 4 for the cylinders and 1 for the downpipe. Can you please add another 1 EGT for my display to read please? the files that you provide only support upto 4 EGT. Thank you!

thank you very much @Adamw! will load these files soonest!

Hi @Adamw, here you go. attached are my ecu and dash's config. feel free to add or change anything. Appreciate your help again. rgds. chemical_fury_021220.pclr chemical_mxs_strada.zconfig

sorry to confuse @Adamw, yes i want the EGT to been seen in both. Currently I can see my EGTs in my ecu, but i cannot see in my dash. thanks for the help!

Hello @Adamw! I searched this forum to solve my MXP read-display problem and fortunately came across with this thread along with your wonderful solution. If you don't mind, can you please add the needful CAN IDs to read my ECUMaster's EGT2CAN (8 EGT sensors) that i hooked up to my G4+ Fury? I tried several times with your guidance and it doesn't seem to work, (which perhaps due to my lack of skills .) Attached are the screenshots of my parameters both from PCLink G4+ and ECUMaster EGT TO CAN. Appreciate your help in advanced, @Adamw. Really looking forward for your reply. rgds. E.