Neville Messenger

Thanks Adam. much appriciated

Hi I've installed a NZ EFI flex fuel sensor and am now looking to add the fuel temp (ethonal temp as it's referenced in PC link) to the CAN stream from my FD RX7 plugin G4+ to my LINK Strada MXS 1.2 dash Flex sensor is wired to DI8 I’ve attached both the ECU and dash configs any help much appriciated Cheers Nev Nev Race Big Font screens 01.zconfig 25 Feb 2024 Flex sensor added.pclr

thanks Adam, that works

Thanks Adam I don't have the Grey, Yellow or brown wires terminated/connected to the dash however I'll look to move it to CAN2 on he ECU board. I note my EGT is sitting at 33 deg C on PC Link however showing 87 on the dash, any ideas why that would be? is there an adjustment required in the stream setting? multiplier/divider/offset?

Hi I’m looking to add a couple of channels to the CAN stream from my FD RX7 plugin G4+ to my LINK Strada MXS 1.2 dash Can you please advise the process to add or update the config for me? Channels I’m looking to add are AN9 - EGT and Digital input 7 - boost switch status I’ve attached both the ECU and dash configs Another question? As you will see from the config I have the dash connected to CAN1 on the ECU, should I be able to connect PC link while the dash is connected? At the moment I’m getting an error in PC link - unable to open the selected com port. If I disconnect the dash it works fine. Nev FD RX7 10112021.pclr Nevs MXS 1.2 Strada - LINK.zconfig

Thanks

Thanks Adam, restore to factory settings and reloaded my map/tune and ECU logging is now working. however.... I can now reproduce the fault. I am running a racetech dash 2 off the ECU serial/RS232 connection. When the dash is connected the fault as above occurs, if disconnected everything works as it should. What alerted me to this was when I tried to restore my tune it came up with an error and wouldn't store to the ECU, disconnect the serial connection to the dash and all was well. what would be causing this conflict?

yeah I viewed your thread earlier, so have you been able to address it with the tweaked version of PC Link?

I'm running a G4+ FD RX7 ECU, Firstly I received this error when trying to retrieve ECU log files - Unable save log file due to corrupt flash pages. Secondly after deleting the exiting log files, when going into ECU log file setup PC Link goes offline... does this every time, unable to make any changes to ECU logging setup as PC link is offline and won't right changes at next connection. Tried downloading new log files and get the same error above The ECU log file setup page shows ECU logging as enabled however I do not see ECU logging status on top right corner of the PC link page (guessing I should see this next to PC Logging status?) Firmware about shows ECU logging enabled help appreciated

Expansion loom 2 installed and EGT working perfectly on AN Volt 9.

Yeah that would do it.... thanks for all your help. I'll investigate using AN Volt 1 or bite the bullet and get another expansion loom

Confirmed its Exp1, tried the shorting with no response.... so is AN7 Faulty? 5 and 6 are configured and working

S7, file attached S7 FD rx7 N Messenger.pclr

Yes, voltage is present at the amp and at the yellow wire on the expansion loom and rises as the EGT heats up

EGT revelectronics single channel amp 0-5v linear output not registering output on AN 7 Volt K type thermocouple wired to in + and – 12v Bat wired to in VCC ECU ground to GND out and Out1 to AN7 Volt Link G4+ FD rx7 AN7 configured for EGT (0-5v) using Cal 5 - 0v = 0Deg C and 5v = 1250 Deg C (amp output in 4mV/deg C) What am I missing? help much appreciated