jrdnclrk

Noted. I also would like to reiterate that the bucking problem still happens when the targets are set to 0 degrees

updated with no changes. I've also tried setting all vvti targets to 0* and the problem stays. Also thank you for the correction on cam teeth. 2jz itb updated vvti to custom.pclx bucking with updated vvti settings.llgx vvti targets set to 0.llgx

i logged this tonight. you can see the bucking in the rpm and tps signals as acceleration goes up. 2jz itb vvti issue.pclxissue with vvti.llgx

Hello again guys. I'm having some issues with my vvti settings on my is300 itb 2jzge. The issue appears to be with the settings from what i can tell. With the vvti turned off the car performs fine under all throttle conditions except the intake cam isn't varying and stays at 0*. Now when i have the 2jz vvti setting turned on using my tps as a load axis. with mildly aggressive settings in the mid range the car bucks like a timing error under transient throttle conditions. Now if i set all the vvti targets to 0* this issue still happens. which has led me to believe the settings for 2jzgte vvti (3 cam teeth) and 1jzgte vvti (2 cam teeth) are somehow not applicable to 2jzge vvti. i have tried the calibration setting in the vvti set up cam angle test selection as well. no effect. I've also tried datalogging this issue but nothing shows up on my logs as far as trigger errors or anything obvious. I'm currently driving with the vvti setting off till i can get this issue sorted. If i have any incorrect info here please let me know. 2jz itb vvti issue.pclx

Hello again guys. I've been daily driving on this set up for about a year now and finally went to different injectors due to a injector failure. ive updated the fuel map for vq35hr injectors. Does anyone happen to know the dead times for these? Also on a side note I got the vvti working correctly. i had previously had the load axis for the vvti set on MAP signal. switched to TPS and works amazing. 2jzge vvti itb DD tune.pclx

small update for those wanting a decent tune using stock injectors and itb's on a vvti 2jzge car seems to start and run decent with these settings. I've only done street tuning on this so no power figures. thank you for all the help. i couldnt have done any of this without this forum!

ok so i ditched the IAC solenoid. it was causing a bit of too much air to get in at all times. adjusted my ignition idle control to get a smoother idle. im still sitting at about 1000rpm and it seems to be pretty happy there. i do have an occasional pop and backfire causing the rpms to go up and stay. asside from that i think its ready to street tune for the fuel map. swapping out media up top for new map and log

I've recently run into this issue when building the basemap for my 1.5jz i would have a single very loud backfire through the exhaust on key on. the solution to this problem was to have a ignition switch input to a Digital Input so the ecu knows when the key is on. and not having the ignition switch set to always on. it will also help with starting as the precrank prime feature can be set to while ignition switch is on. Just adding this input 100% solved this issue for me. i recommend using your DI3 input for this cause you dont have anything allocated to that yet.

I’ll adjust when I get back to the car. My throttle stops are pretty well closed but I’ll have to double check I haven’t rattled some linkages loose. I may also perform a smoke test to see if I have any excessive vacuum leaks. Between the map and throttles.

I have all the runners tapped and hoses ran to a vacuum block. The map signal is also ran to the block. The iac and brake booster is also ran there.

ok map is plumbed in and calibrated. ive got the car starting and running but the idle is all over the place. i was previously having fuel pump issues. This is300 has a few gremlins that needed to be addressed. so the open circuit relay and the fuel pump relay are doing their job now.. that may have been the source of the wideband issue but im not going to say its not possibly faulty.

ok so i think I'm having an issue with my fuel pump. It seems to be losing voltage. shortly after the start

hello guys. I've gotten myself into a point where i think I'm chasing my own tail and i need some one with a bit more experience on building base maps. current set up is a 2jzge vvti, has itb's, stock non vvti injectors, stock ignition coils, monsoon running batch fire, wideband is an innovate lc1, ford two wire iac. stock cams. fuel and ignition maps are set to alpha N loads the car seems to start under extended cranking and no throttle inputs. again im unsure of appropriate trigger offset and this could be my whole problem. unfortunately i have no assistance so cranking while using the timing light is not possible. if I could get someone to just double check my map and log to see what issues I may have that I'm unaware of I'd greatly appreciate it. EDIT: uploaded new map and log

https://harmonicdampers.com/index.php?main_page=product_info&products_id=240

Hello thanks again for the help! I was able to resolve the issue by changing the way my pre crank prime works. I had previously had it set up to precrank prime as soon as the ecu is keyed on. i changed it to as soon as the ecu see start signal. i also added an input for the start signal to digital input 2. all is well car now fires up easily and the main problem is resolved!