Wee Chia Yung
Members-
Posts
30 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by Wee Chia Yung
-
Thanks adamw, vvt working already, do you have the basemap for vvt table?
-
-
Intake cam sensor to di1 Vtc solenoid to aux 2 Exhaust cam sensor to trigger? Need 3 wires connected?
-
-
Ok thanks, Under inlet bank 1 menu, cam sensor input di1 need to connect to where
-
I would like to set aux 2 for vtc, vtec high/low already set by using aux1
-
-
-
-
DI3 connect to gearbox? 3 wire which one? I need speed input then when car moving i need send a signal to lock the reverse gear. Pls help
-
New problem I test aux 1 using a light bulb not working, but aux 6 is OK, is it ecu problem?
-
Monsoon digital input 1 to intake cam sensor, aux 2 output vtc When I adjust vtc map aux 2 no working Digital 3 connect to speed but nothing happen also... Please help
-
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Set to quiet mode, working fine without noise, thank you -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Aux 5 active state set to low already, tps calibration done, but pedal still not working, please help After aux 5 active state set to low and tps calibration I can see the throttle automatically open then close. After tps calibration done, I press the pedal nothing happened to the throttle This map is working when I press the pedal, but throttle not moving OK I think I found it to work, set when stalled to run throttle and e throttle 1 target map, correct? But I notice when I put the key to on position, the throttle making sound, is that normal? -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Dear Adamw, is my wiring and setting correct? I've done aps calibration, tps calibration got problem. -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
And then, I have connected pedal signal 1 to an volt 3 and 1 to and volt 4 is this the setting for the pedal signal? ive found main and sub already but still not working, which part I did wrong -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
this is the setting you provided, it's different from mine i have connected an volt 1 to stock throttle pin 6 and an volt to to pin 4, but my software can assign 1 an volt only... And then, I have connected pedal signal 1 to an volt 3 and 1 to and volt 4 is this the setting for the pedal signal? -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Adamw, e throttle still not working, I've connected e throttle module green wire to aux 4, brown to aux 3,white to aux 5, correct? Adamw, e throttle still not working, I've connected e throttle module green wire to aux 4, brown to aux 3,white to aux 5, correct? -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Adamw, just to confirm, pedal wiring, do I need to connect to linkg4 ecuļ¼or just take the throttle 6 pin you mentioned b4, no need any connection from the pedal socket -
linkg4x monsoon k20 link e throttle setup and wiring
Wee Chia Yung replied to Wee Chia Yung's topic in G4x
Thanks Adamw, how about the link software setting, need to assign an volt to something? And aux to something confusing Sorry Adamw, the wiring diagram you provided, throttle pin 2, connect to 3 location? E throttle module yellow, ecu 5v and any ecu an volt input, correct? -
Please help me with wiring and software setup K20 stock electronic throttle got 6 wire out, I need to connect to where? I'm now using linkg4x monsoon and link e throttle module I need how to setup the software also, too confused with an volt and aux
-
Yes manual transmission, don't know which wire to cut and link to monsoon, can help?
-
Hmm I'm thinking using monsoon for tuning and factory ecu for other function
-
How to wire monsoon parallel with k20 ecu, can someone help