smallthecat

downloaded new update software etc. tried multiple times to upgrade but same error. green bar sometimes makes it further across than other times. have battery charger connected to battery. power to ecu at 12.25v. tried legacy downgrading, no luck same issue. tried changing com port to 50 and was worse. no other com ports are in use. any other ideas? events in device manager Device FTDIBUS\VID_0403+PID_7069+5&9bd1446&0&1\0000 requires further installation.

+1 I'd definitely consider getting a link for my X if it were available, the reflash softwares UI and the time involved reflashing is a pain. Link has a much better ui, user friendly and mostly easy to understand. Would such a product be able to retain all of the factory ecu's features?

Set at .2v and .5v already yeah. Haven't been able to get it to start and the timing light I have won't work with a low signal unfortunately, it might be broken so I have ordered a new timing light. Changing the base timing around from -360° to 0° to +360° seems to have no effect on the stroke of the engine. As in, you'd expect one to be the exhaust stroke and it splutter or kick flames out the intake but nothing happens moving the timing offset. Thoughts on why that could be? I've taken plugs out to let the cylinders dry out and it seemed pretty wet in there. Maybe once it dries out moving the timing will do something Where is a good place to start for my base timing if the engine is setup to factory TDC settings? Does injection timing need to move to align with the base timing once its set close and running? Injection is currently at 400btdc on the base map but if my base was -120° then would I bring that back 120° aswell? disregard injector timing question, there's a good explanation in the help menu.

TriggerScopeLog10.llgx

this scope ok? trigger is always counting or saying tooth after sync. Can't wrap my head around it. TriggerScopeLog4.llgx

New log and trigger scopes. Still just won't start, did fire a couple times. Changed to 1800cc and 2000c but could smell fuel so guessing too rich. Think I logged all that as well, made changes during log. Any Ideas? Must be timing I think? Anyway to tell where I should be setting BTDC using the trigger scope? PC Datalog - 2022-04-22 9;31;32 am.llgx TriggerScopeLog.llgx TriggerScopeLog2.llgx

Yeah I'll shoot down and try get another scope, that's weird that scope has no info now I checked it before I uploaded it. I will also try increase capacity and see what happens. ITB's are synced, haven't touch them since it was last running. WIll double check though. I pulled coil 3 out and got spark on my chassis. Haven't tried 4 but assumed if 3 had spark then 4 also would.

Start Up Tune V2.pclx TriggerScopeLog.llgx PC Datalog - 2022-04-17 4;53;59 pm.llgx So I changed the Map sensor to a Honda sensor that works. Car starts, but only running on 2 cylinders. unplgging coil 3 and 4 to test them showed they weren't firing. Tests through ecu to injectors and coils are fine all have a signal and work when tested to the correct cylinder. I've just changed the rear main seal as it went last start up, so ideally want to fix this issue before I start it again, gearbox out and in isn't fun. Compression tests on all 4 cylinders read between 200-220psi. Haven't done a leak down test as my compressor shat itself just as I was about to do it. Is there anything wrong with attached tune, triggers, log that stand out? Cheers So in firing order its firing on 1 and 3, 4 and 2 not firing.

1 - ground to ground out 2 - signal to an volt 2 3 - 5v to 5v+ Only info I have is this. 1 - e2 sensor ground 2 - pim? 3 - vc ?

Unplugging gives me a 0v reading. My tps also reads 4.95v on pc link. Is it an earthing issue? I'm confident my pinouts are correct. If I unplug and test the connector it reads 4.99v to the map sensor and the signal reads .03v unplugged. Both of earth's are to seperate earthing points on the block. And I have a solid earth to the oe chassis earth from block.

Roger. Probably the pinout. Will try that out later on and check pinout. Doesn't run very nicely with the map reading incorrectly. I used your 16v with 20v itb fuel table and ign table I found on another thread as it seemed like a close alternative for a startup as I had lost my previous tunes, I was having trouble with pc link acquiring a connection to the ecu so reinstalled it and during that troubleshooting process and lost my old data unfortunately.

Yes I re wired everything with new connectors etc.

Bap around 100, map around 150. Last reading I got was BAP 98.6, Map 144.7. Set to the linear cal settings as above.

Yes I realise that the calibration table is incorrect now, would this be because I've changed the vacuums? How would I recalibrate it using the linear table? Not 100% on how to set these up or recalibrate them at all. AdamW gave me the factory map sensor info above.

I've since deleted all other vacuums off the intake and my MAP reading is too far out to calibrate with the BAP. Is deleting the other lines going to effect the values in the linear cal table? I've got it running again but changed the values myself to bring them into range. It's idling and in general running roughly, coughing spluttering.