TOMMYFD
Members-
Posts
57 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by TOMMYFD
-
Hi, I would like to know if there is a way I can make my launch control active state show up on my IC7 dash. Regards
-
I didnt confirm with a 0% and 100% iIjust did the calculations as the help file is saying. I have no clue of what numbers to put in my accel cold correction table how will I calculate those?
-
https://drive.google.com/file/d/1YWLNY2QxAwP2MwBorKSAG2NFTbvlVmcY/view?usp=sharing
-
https://drive.google.com/file/d/1bZUOM4a9Rj9vwi4h9dFngAjqpfwgp8uH/view?usp=drive_link https://drive.google.com/file/d/1QXuNZRo0N9t3GIH-0cPt7CxAqFqNk6Jj/view?usp=drive_link This are my loggings with 6 inj events on stagged. I go really rich when secondaries kick in then back to normal. What do I have wrong here?
-
Thanks a lot Vaughan very helpful so i dont need to do anything just increase my fuel pressure. Thanks again.
-
Shouldnt i be in closed loop lambda so the ECU can calculate the desired mass of fuel?
-
So how can my injector duty get reduced if my maps are the same?
-
Just lean out my fuel map?
-
Thanks I will try the accel fuel and see the difference. Something else I want to figure out is im out of injectors at 7700@84% duty cycle and I want to rev to 8400. Im in modelled mode with fp sensor fuel system type and im currently on 48 psi base pressure if I want to increase my base pressure to 56 psi the only thing I have to do is lean out my fuel map or should I change anything else in my settings?
-
https://drive.google.com/file/d/11q8Rgz5PFKqVijKO4cPuCfGtLPBj6s6p/view?usp=sharing https://drive.google.com/file/d/1N6Arz7OQ65KwTWW-sJPAkad5eFz_qcKW/view?usp=sharing
-
Hey guys got an issue and don't know if this is normal or if I have my staging ratio wrong. My afr's are good but when my secondaries kick in I lean for about 200 milliseconds then my afr's go back to normal is this normal or should i play around with my stagging ratio?
-
The timing light i should have it on atdc 20?
-
thanks pete I will try it out tomorrow and let you know thanks a lot!!
-
first start update.pclx I changed the pri/sec ratio and the secondary injection staging table
-
PC Datalog - 2023-07-29 4;59;04 pm.llgx this is my log with 5 inj event accel fuel. I hit primary injector duty cut. any help im really confused what do I have wrong here?
-
https://drive.google.com/file/d/1J0ezrw80GApPcxnNWsEKd4ZirplWEl1Z/view?usp=drivesdk first start update.pclx
-
The datalog is to big for uploading it here It leans out about 2-3 miliseconds
-
Hey, i got an issue when my secondaries kick in the car leans out for a split second is this ok?
-
Thanks the trailing split table should i undo it after the calibration and put the numbers I had before?
-
Hi guys. i would like to know the procedure of checking my base timing on my Rx7 FD S6.
-
Hey guys dont know what happened everything was working fine and today when i hooked up my laptop on the ecu my layout vanished and i cant find it anywhere. I have 6 layouts on the load layout tab but none of them seem to be the one I had. The real promblem is that my logging time plots on the other tabs are all white and before they where different colors and also on the y axis are only 1, 0.5, 0, -0.5, -1, and I cant see my logs.
-
Hi, Im trying to sort out how to calibrate my garrett speed sensor with a 9 blade g35-900 turbo charger any help please