Wheelspk

thanks man this has been a big help from you...will test this out and report back .

@Adamw so here is my log i took of just driving around from 1st gear till 5th ..then again from stop 1st till 5th. what should i do next to get my gears to display in the pc link softwear. sorry had to use google drive as the file upload was bigger then allowed here. https://drive.google.com/drive/folders/1X5huxkrvQvMxpB89LnkiULvPWkrwRHSh?usp=share_link

@Adamw okay ill take logs and post of all 5 gears on the highway.

okay so my tuner had these parameters set for gear what changes so i make too gear too show up? https://ibb.co/THvMSZp https://ibb.co/whQv975 https://ibb.co/TwXRbXC https://ibb.co/VCxmb9f

hello, how do i get gears to display on my ecu pc link? evo 8 5 speed.

@Adamw yes i know i will take the pin out of the oem cluster connector and i have disassembled the cluster with the niddles out and only using its circuit connected with the oem harness fooling the car too think the oem cluster is still attatched. the digital dash and the oem cluater all is working good... i just want the fuel level too show up on the powerdigital dash. i have a CAN based digital gauge cluster now which i want too have the fuel level displayed from powertunedigital so if my ecu sees thw fuel level i can have the digital dash display it.

@Adamw yes its temp 3 at pin 77 thats what the my remote tuner told me too hook the fuel level sender too if not pin 77 where else can i hook it up too? i do have the stock cluster coz evos tractions and abs starts acting strange if its not hooked up to the oem cluster. if i hook up a 100ohm resister in btw the wire from the cluater to the ecu will it not dempen? or how and where do i need to hook up the resistor if not there and what size resistors. let me know.

hello, im trying to get fuel level too show up in pc link on my jdm evo 7 my wiring guy told me too hook up signal wire from the oem gauge cluster as the evo has two floats so both sender units should be joined at the cluster... he told me he will hook up a wire from the cluster fuel level signal too pin # 77 on my ecu pin#77 being empty, my question is will that work to get the ecu too see fuel level? how do i tell the ecu thats pin#77 is fuel level sender signal?

@Adamw on the diagram it shows that the fuel level sensor is supposed to have a ground? so i put extra ground on one of the sender sensors?

yet thanks for the answer... ill have my electrician fix it ....lol you make mistakes you learn

@Adamw when i took my evo 8 oem cluster off and my link lamda stopped working :/ as soon as i plugged it back it and it worked again... whats up with that? and im back to the drawing board, i cant remove my oem without the Lamda not working. i have no idea what link lamda has to do with Evo 8 oem cluster

okay ill give it a go and report back if im stuck on anything. thanks @Adamwas always

also im not sure but i think evo 8 fuel sender reads in ohms instead of voltages. so would i have to use i put units as ohms or volts on the pc link software? @Adamw

@Adamw yes evo 8 has a saddle type tank meaning 2 fuel level sensors, do i need to empty my tank and put 25% then 50% 75% then 100% fuel to take reading and do input in the cels? i should be taking the voltage reading on the AN volt after i have combined the two level sensors in series with circuit you have provided? also on the diagram it shows that the fuel level sensor is supposed to have a ground? so i put extra ground on it or will my oem ground be okay?

my car is a evo 8 and it has a saddle type fuel tank which im surw has 2 floats which makes it even harder for me to figure out how they would connect to give reading as one level. @Adamw please help as im out of ideas.