TheChrisLeonard
Members-
Posts
20 -
Joined
-
Last visited
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
TheChrisLeonard's Achievements
-
Vaughan reacted to a post in a topic: Haltech GPS speed module setup
-
Ahhh ok i didnt think to look at that either. I figured that was all for normal wheel speed sensors not for the gps input. Makes sense though!
-
Ok so since i have it as “gp speed” the ecu knows this is for vehicle speed and it will set the units to what type i selected? I Was confused because theres no table for the calibration just a value. I updated it 500. Thanks!
-
TheChrisLeonard started following Alternator draining battery through aux output. , Haltech GPS speed module setup , Can I get gps tablet to display speed in pclink and 2 others
-
Hello, i have a haltech ht-011310 gps speed module. It comes with instructions to set it on haltech but i’m guessing on this. I have it set to di1 and under GP speed. The instructions say it is calibrated to 5000 pulses/km and 83hz. I set the calibration for 5000. Is this right? How do i set this up for mph? Thanks
-
I have an xtremex and I use my tablet as a display and tuner. Is there a way i can use the gps on the tablet to work in pclink as my speedo gauge?
-
Volvo electro hydraulic Power Steering Pump CAN Control
TheChrisLeonard replied to TheChrisLeonard's topic in G4x
I havent gotten an answer. I ended up running an mr2 pump -
Ford Coyote Gen 2 sensor calibrations
TheChrisLeonard replied to TheChrisLeonard's topic in Engine Tuning
@Adamw alright awesome! Thank you! Also would you happen to know if i can power a bmw electric water pump pwm wire with the xtremex or is it fine if i just run 12v to it. -
Ford Coyote Gen 2 sensor calibrations
TheChrisLeonard replied to TheChrisLeonard's topic in Engine Tuning
@Adamwwould you happen to have the coyote head temp cal? -
Hello, does anyone have the proper calibrations for a 2017 Ford Mustang Gt. I am mostly looking for the Head temp sensor. It seems like the falcon sensor works right. Also looking for the calibration for the Oil pressure sensor for Performance pack models. thank you!
-
Hello, I’m looking at running a volvo pump on my car and before buying a controller, has anyone figured out the CAN to control pump speed? I have an xtremex so i’m sure it can be done. It looks like it just needs vehicle speed to control the pump speed. This is a drift car so I need the pump to run at full power. Thank you!
-
Alternator draining battery through aux output.
TheChrisLeonard replied to TheChrisLeonard's topic in G4x
So i measured everything with the alternator unplugged. Its really difficult to get in there with the alt plugged in but i can try to get in there. With the car running i was seeing around 10 amps from the aux out and with the car off and ignition off i’m getting .3v from the aux out. I only have that one wire going to the alternator on pin two and the ring terminal. Here is the connector pinout for it. -
Hello, I have a 2017 coyote engine with an xtremex ecu. I have aux output 6 outputted to control my alternator. The battery is draining through the alternator if i have the control plug in and when i check the aux 6 it stays around .3v with the ignition off. Is there a way to stop this or is this normal? The car charges fine with no alternator control attached but i would like to keep it since its available.
-
TheChrisLeonard reacted to a post in a topic: Car runs only with starting fluid
-
I ended up ordering the holley coil drivers. I was considering smart coils but many people have had success with stock coils. It can always be changed in the future too. I’d build a new engine harness
-
TheChrisLeonard reacted to a post in a topic: Car runs only with starting fluid
-
Ok ive been told multiple times i dont need them… should i run ignitors or ls coils?
-
TheChrisLeonard reacted to a post in a topic: Car runs only with starting fluid
-
Does the factory 2017 coyote coil ned an igniter? I measure .8-.9 ohms on the coil.
-
TheChrisLeonard reacted to a post in a topic: Car runs only with starting fluid
-
here is the latest crank log, looks like theres dwell now Still no start but theres spark so i'm going to do base timing next CNS 3 PC Datalog - 2022-06-2 6;13;58 pm.llgx