-
Posts
71 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by Bud
-
-
Dear Scott,
Thank you very much for your answer and your advice.
i will try.
do you have basic mapping setting for knock control for subaru for help more?
Regards
-
Dear All
I have just finish my mapping on fuel SP98 of my car
My car is subaru Gc8 with engine 2.5l manage by Vi-pec v88, injectors 1300cc.
I just connect knock sensor to my vi-pec v88
My knock sensor is bosch sensor
Some body can help me for make basic setting on the knock system?
Best regards
Ludovic
-
Hi Bud,
have you setup your 2000 cc injectors properly in the software, injector dead times etc,etc.
Can you post your PCL file so we can check your settings.
Also what fuel pressure are you running.
Are you planning on running ethanol or some form of race fuel to warrant using such big injectors.
Regards
Dave.
Dear Dave
Thank you for your answer.
Normaly yes i made setting.
my plan is made E85 after fuel unlead
i join to my pcl can you check
fuel pressure is 3b or 43.5 psi
regards ludovic
-
Dear all
i start my mapping on my subaru.
But i had one problem. Now i use injector dynamics 2000cc.
The idle is not stable i try change fuel mapp but nothing . it was stabe when the car is rich nearly at 12-11 AFR but i want 14.7 at the idle impossible. the idle jump up (1500 rpm) to low ( 700rpm)
before i use 1000cc bosch and never i had problem the idle was perfect.
can you help me? some idea?
regards
-
Hello
my ame is Ludo and i am new on Vi-Pec ECU.
I order to the french dealer one Vipec V88 for my subaru Impreza P1 and i will receive it soon.
I have some question for you:
i want install DBW system from Subaru Impreza hawk EJ25 year 2006-2007 model
can you help me for the wiring? do you have the wiring OEM of the pin out of the plug of pedal and the plug of electronic throttle
regards
-
Sear SimonÂ
i know this sections but no information on this function
-
Dear all
I had one Link plug in on my subaru impreza V5-V6.Â
I see on the documentation of pin out function : AUX INJ 6: Main relay (ecu hold relay)
But on the documentation is not write the pin out of Harness of the car.
do you kmow which connector and pin out where is located this function?
thank you in davance for your help
Best regards
-
Dear All
I search one system where i can connect 4 lambda wideband and may be 4 EGT with analog output forconnect to my LINK G4 Extreme
Because i want made mapping cylinder by cylinder
do you have something and some information?
best regards
ludovic
-
Dear All,
i had one Link G4 extreme and i want install to my subaru with DBW .
but sometimes i read if you had silver box you can connect directly and if you had red box you need one module for DBW.
why 2 configurtaion different? when i bought it i want use e throtlle and now i am not sure i can use and nobody tell me this difference.Â
i think i had red box
If the red box can not connect directly DBW what is in PIN aux 9 & aux10?
best regards
-
Dear All,
How are you?
I want to connect on my Link Ecu the new model of sensor Flex fuel from Continental
It is this sensor:
Is it working with Link ECU? how to do connect to ECU?
in advance thank you.
regards
ludovic
-
Dear all,
Can you tell me on the expansion cable for the ECU Plug in for Subaru V5-V6 which color of wire for each output or input?
best regards
Ludovic
-
Dear all
What is Dyno realtime parameter,
How to do works this parameter and how to do for use thie parameter?
regards
ludovic
-
Dear All,
i have a ECU Link plug in connected to my subaru V5-V6.
I search an good setting for the ALS system with the standard sensor on the engine. and i earch an good setting for the lambda respopnse for the Autotune.
Can you help me?
Best regards
Ludovic
-
Hi all,
I have ECU LINK plug in installed on my Subaru v5-v6.
I'm trying to replace the dashboard original by one  dashboard AIM MXL to be connected by CAN .
As soon as I unplug my dashboard original, info that comes from speed gearbox and goes into the computer no longer works. I watched as calibration information in theECU Link.
I noticed that the tab Pull up resistor is OFF.
If I put in the ON position do you think it will work? Do you have an idea to help me?
Thank you very much in advance.
Best regards
Ludovic
-
Hi Simon,
I test with calibration V7-V9 map sensor.
And it will be working and i can calibration with success
Thank you in advance
regrads
Ludo
-
Dear Scott
My firmware version is 4.9.1
Regards
Ludovic
-
Dear all
I have one ECU Link plug in for Subaru v5 & V6.
I use all sensor standard from subaru.
I can not make MAP sensor calibration by the software.
i have this error message :
MAP SENSOR CALIBRATION COMMAND FAILED: CURRENT MAP inf 5KPA or sup 5KPA OF BARO READING.
Can you help me? because i have delay when i check boost pressure Defi gauge and the on the link software.
Regards
Ludo
Â
-
Hi Scott
thank you very much for your answer.
I find JST connector 5 pin, is it possible ti give me the Pin out of JST conector for i can built my harness for the Dashboard?
In advance thank you
Best regards
-
hello
I just bought a G4 plug in ECU for my subaru STI v5 - v6
Originally there is an ignition coil. I want a past one ignition coil per cylinder. is it possible to use the outputs from the computer Ign 1 ign2, Ign 3, ign 4 for controlling the ignition coils.
Thank you in advance
Ludovic
-
Dear all,
i order for my car a link Ecu G4 plug in for my subaru V5-V6.
I want connect Aim dashboard on the ECu. it is possible?
in advance thank you
Mitsubishi Lancer Evo IX base map with Mivec
in G4+
Posted
Dear All
I ordered one ECU plug In for my Mitsubishi Lancer Evo IX.
I download PC Link software but i not find inside base map for Mitsubishi Lancer Evo IX with Mivec system
You have just Mitsubishi Lancer Evo 8 without Mivec
Is it possible to send me base map for my car with Mivec? I want prepare the base map
Regards
Ludovic