Cnstman

Please fix this.

Thanks.

New release today! https://www.linkecu.com/software-support/pc-link-downloads/

subscribed. I had this issue once on my 04 USDM STi. I did both of the ethrottle relearns and so far it has not came back.

wondering the same thing

The cruise control feature works great, however I have tried and tried, but I can't get the cruise control light on the dash to indicate when the system is enabled, or active. Any advice?

No issues with Windows 10 here either.

Ok, thanks for all the help. I do have anvolt 11 working, I just could not remember which pin its wired to. Having access to anvolt 12 is a help as I needed one more input.

Thanks. Those diagrams show anvolt11 in 2 locations.

Per my first post I have a 2004 usdm sti. Thanks for the info. I also have the smaller 4 pin expansion harness. I can't find the wiring pin out for that in the help file. Do you have that?

Simon: What about AN Volt 12?

Hello, I have a Subaru I88 V10 plug-in for my 2004 USDM STi, and I need another Digitial input. The help file does not show which wire in the expansion connector to use for DI11. I see DI11 in the inputs, just need to know what wire to use. Thanks! Aaron

I upgraded to windows 10 and have had no issues. thanks for the input.

My IQ3 Logger dash works great. Below are the settings I was advised to use by Racepak. They don't monitor their forum much, but the tech dept. got back to the company I bought the dash from with-in 30 min and I had my answers. Can 1Data Rata 1MBPSCAN ID 1000Data Direction ECU TransmitTransmit Rate 20 or 50 is avail.

Has any testing been done with Windows 10 and the new PC Link software?

I have the siemens ethanol sensor which according to the help file requires an external resistor. Can this sensor be shared with no external or pull up?

hello, I have the output wires from my zeitronix ethanol content gauge hooked to ANVolt 4. Its calibrated correct, and the ecu displays the same value as my gauge. I see with the new firmware there is a specific DI labeled ethanol sensor. How can I tell my ecu to use anvolt 4 in stead of this DI? My ecu is a 2004 usdm Subaru Sti plug in. When I go to the MISC runtime page the ethanol % always shows the fault value assigned in the DI for ethanol sensor, it does not show my ANVolt 4 value which is correct. Liikewise my startup tables are using the fault value data vs the correct data from ANVolt 4. If I need to re-wire, which pin on my ecu is the ethanol sensor DI? the help file does not provide this info. thanks Aaron.

Finally have my car running again and I am playing with this new feature. Can you explain how the cruise control should work on my 2004 Usdm Subaru sti? I can get it to work from time to time but have to hold in the button on the stalk and push down and release the button just right while still pushing down then release. I can't get the accelerate or coast functions to work at all. Any help would be appreciated.

Found it in the help file, looks like it's in the expansion connector, along with the new temp 4 input as well.

The new firmware / software has added An Volt 12 to my Subaru V10 plug in. I can't find anything in the help file that tells me what pin is associated with AN Volt 12. Is it in the expansion harness? If so, which pin? Thanks Aaron.

1ms for ID2000 as well?

According to this, 5.4.1 unlocks everything in the link? http://www.linkecu.com/forums/link-g4-e ... t/63542560 I have a similar feeling about vi-pec vs link. I have a top board plug-in vi-pec, that is now considered a link.

Did you ever get this working properly?

hello. I have a vipec pnp i88 board for my usdm 2004 subaru sti. I guess this unit would now be considered a link g4+. Has anyone tried the racepak 230-VM-EFILINK vnet Canbus cable and ran a IQ3 digital dash?  I have found some info on people using the racepak vipec v44/v88 cable over serial with mixed results. I figure this cable was designed for G4+ ecu with can onboard results may be better. Thanks.Â

the cruise control buttons work great, but now this ecu has actual cruise control, which for street/race cars is a great feature. Â I am considering using a different 'map' for the drag strip that has them set for anti-lag, start the logger, etc, and one for the street so they are cruise control swtiches.