Jump to content

Jonas Eriksson

Members
  • Posts

    21
  • Joined

  • Last visited

    Never

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Jonas Eriksson's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. As topic Recomended solenoids for S50B32 dualvanos with Link? Does LinkG3 support Dvanos..or do we need to go for the "plus"?
  2. Hi! We have an issue with out VR6 N/A car...the 12v once -92 We put the Bosch motorsport 0 221 503 002 3x2 coil + Link ignition 3 channel ampflier and we get a knockdetonation on the 6th cyl when reving from idle standing.....even if we lower the ignition degree to like 5 degrees When changing to distributor appl the car runs good but without knocking..though..it feels like it has 50hp less then with the 3x2 bosch coil. Anyone have exp regarding VR6 engins? /Jonas
  3. Hey Link! Do you have anything ready with VANOS maps for the S50B32? (BMW M3 3,2 Euro), we need a system that maintain the full VANOS function and still let us tune the system. Do you have a VANOS map u can suply? iam unsure we can tune the vanos our self correct on the dyno / Jonas SWEDEN
  4. Can i use the LINK tripple igniter to boost the M5 "Coil on plug" ignition with my G3 on a S38B38 M5 turbo engine? , or do i have to use for ex a MSD DIS4 box? We are using E85 gasoline(ethanol)and want to put out 800-1000hp http://www.realoem.com/bmw/showparts.do?model=HC91&mospid;=47387&btnr;=12_0429&hg;=12&fg;=05
  5. Ok, thanks for tips Tim! But will this coil handle 700hp ??
  6. I have a turbo subaru motor in a sandcar with an older link unit. At 4700 rpm the motor begins to misfire. It sounds like it's hitting the rev limiter. The rev limiter is set at 6800 rpm. I set the programmer to the test rpm page then brought the motor up to 4700 rpm and noticed the readings started to jump around. With this info, the problem seems to be more ignition related rather than fuel. I have tried 3 different computers, a new coil, new spark plugs (gapped to .024"), new resitor spark plug wires, new timming belt, new cam sensor, checked all grounds, tried 3 different ignitors and I still get the same problem. It runs smooth up to this rpm level. It almost seems as if there is some sort of feed back or interfence signal that is corrupting the low voltage signals. Is it possibe the suppressor on the coil power supply might have gone bad causing voltage spikes? What else can I look at to determine were the problem might be? > <br> >Thank, mike martinez <blockquote> I had similar problem this summer on my 6-cyl engine...but when i changed in "dwell" between risin and falling...it solved my problem, i dont know if u can adjust this...just an idea /Jonas
  7. What coil should i choose for the G3 ? , its a BMW 6-cyl turbo, want to run wastedspark application instead of the oldschool "rotor" system. Is there any good choice of BOSCH coils? have u tryed 3pcs tower MSD coil along with the trippel igniter? suggestions needed!! Best Regards Jonas SWEDEN
  8. Can i adjust so it cuts both fuel and ignition ? I heard on this "old" 12v Bmw 6 cylinder engine the rocker are very sensitive to hardcut and "backpressure/exhaust shoots" , they brake to earlie... any suggestions?
  9. PROBLEM SOLVED!! mixed up "falling and rising" dwell....im using MSD so it should be falling!
  10. When about 85-90 degree limit is set to 7000rpm and 240kpa , no other limit is activated.. i tried to shift polarity on trigger sensor...didnt not make any diffrents...just alittle better idle i think, and 0 trigger errors....before i had about 3 this is making me crazy
  11. I talked to Simon/Link over Skype last night.. and we found that the arming threshold voltages were like shut of after 2000rpm..they were set to 0.0 voltage , so we changed them so we have higher voltage up on higher revs.. it feels really like this was the problem..i will go out in the garage and download this numbers soon..and try to rev it up. /Jonas
  12. Ok.. We are using a 60-2 toothed gear with what i think is called a magnetic VF sensor. (BMW STD PARTS) We are also using the PN6600 MSD HVC coil pack system. Do i have to set any type of dwell time? We are right now up to start it up for the first time...just going trough alls ensors and such. the engine is still the M30B35 engine...6-cyl..
  13. http://catalog.meca.se/Upload/images_web/KVMZ0324.jpg http://catalog.meca.se/Upload/images_web/KVMZ0540.jpg This is how it looks...same type as Volvo 760/780
  14. Hey there A! Sorry for lack of information! As i can se...there is a cable connected thrue a "ring" on 1th cyl cable..and there is also a crank sensor BUT it only runs to the diagnostic output?! So iam very unsure how it works...the ecu is a bosch ecu and made for boost as it comes like this from Bmw fabric! , regarding the sensor info i guess i have tot take it apart to see how it operates?!
×
×
  • Create New...