Jump to content

George GEP

Members
  • Posts

    92
  • Joined

  • Last visited

Everything posted by George GEP

  1. Hi can anyboy share Base VVT (intake/exhaust) maps for GEN2 Coyote 5.0 ?
  2. here is log file https://we.tl/t-MG7lubtw5P
  3. basemap.pclr i can not upload log, i am limited to total size 175kb which already filled by pclr file
  4. Hello i have wired AEM Wideband through can, i see figures all is working but Closed loop lambda is not. i mean it doesnot correct at all no matter what i set. Auto Mode (Wideband) Stoich mode (Wideband) ecu does no correction but if i wire Wideband through Analog input, then CLL works just fine. does anybody have same issue here?
  5. i would like to use outputs fan, fuel pump, meth injection etc so i want to get rid of Relays and use PMU instead as well as attach keypad for engine start etc functions
  6. Hello, can anybody support with ECUMaster PMU and Keypad installation setup? does it work with Link at all? any success? i'm running Link G4x Storm on my car for which i got PMU and 12 key keypad. would need assistance with setting it up and make it work. thanks in advance
  7. hello, please suggest what budget friendly PDM and keypad is suitable Link G4+ Storm and is there some presets / configurations available? thanks
  8. Can anybody post VQ35de RevUp stock VVT Maps for both, intake and exhaust? Link base map includes intake vvt map which is also bit different from Revup engine. thanks in advance
  9. trigger 1 and trigger 2 both Rising? or falling? or ?
  10. see this one https://we.tl/t-p3IhugUqNL
  11. by mistake i opened same thread in G4+ section Please check Trigger scope file and map file both are in link below this is VVT LS Engine (not sure which one) what trigger settings should be used for this engine? and what offset to calibrate timing now it is selected LS1 5-10 i see rpm signal in log, but engine stops while cranking - meaning wrong base timing i just dont have timing light on hand https://we.tl/t-p3IhugUqNL please see and advice thanks
  12. wiring issue was that main 4 ground pins were attached to painted surface on a car where ecu was not getting ground so ecu was powered up from somewhere else but nothing worked also fuel pump which was on Aux4 wired through relay was not connected to ecu as well. not sure was it fed from trigger wheels or somewhere else. but once ground wires attached properly ecu started working fine but issue with failing Aux4 status. any thoughts?
  13. here is Map and triggerscope link together https://we.tl/t-HF3ozH2bZB please check
  14. here is triggerscope please check LS engine with VVT it looks like L99 engine. is triggerscope and settings correct? triggerscope log1.llgx here is Map and triggerscope link together https://we.tl/t-HF3ozH2bZB
  15. Aux4 goes to fault as soon as im trying to activate it or test it does not matter what function will i add to it it says fault immediately as soon as im trying to activate. i removed pin completely from aux4 and tried.. still fault other aux pins work fine what to look for?
  16. investigating wiring side now, thanks will report
  17. will do, and? what to look for did bench 12v and gnd on table https://wetransfer.com/downloads/8718f918f45cfada2ed162576a0475c920200626082405/e5bd64f5b7ac99013250cea2aacc75ee20200626082420/7d0101 here is file and log did bench 12v and gnd on table https://wetransfer.com/downloads/8718f918f45cfada2ed162576a0475c920200626082405/e5bd64f5b7ac99013250cea2aacc75ee20200626082420/7d0101 here is file and log
  18. https://we.tl/t-JkmLHVqs6x nothing changed
  19. i can give you Team viewer access to laptop to check yourself what a weird stuff is going on. https://we.tl/t-JkmLHVqs6x new file
  20. what a dumb forum i can not post small screenshot why is it limited so much in size? 10kb? seriously? :)) anyways i have all sensors disconnected and i see 4.02V in analog inputs on ANv2 and i see 3.3 / 3.8 Volts on TEMP1 TEMP2 when everything is disconnected OR connected. nothing is changing and none of other parameters react such as MAP, trigger or something. 5volt out from ecu does weird thing, sometimes it gives ot 5v sometimes 10v sometimes 2v. is that normal?
  21. updated firmware. still same nothing changed
  22. ok will try now. and report. have u checked files that i posted?
  23. here are both files on this forum i can not attache more than 0.01MB file so i uploaded it to wetransfer. https://wetransfer.com/downloads/c186ef3a2db173865847d11418d60cc620200626060754/20466762d31dfe4024aec78dfdba67c620200626060807/6a9a40 please check and tell me what am i missing
  24. i have got new Storm x, migrating tune from old Storm. i selected parameters one by one probably nothing missing but strange issue is that nothing works, no input no output no reaction on ecu side. in run time values i see no reaction from TPS, MAP etc wiring is there something different in X than in older ecus? is pinout different on X?
×
×
  • Create New...