Jump to content

Lawrence martin

Members
  • Posts

    48
  • Joined

  • Last visited

    Never

Everything posted by Lawrence martin

  1. hi scott I have unistalled again and then deleted both pclink and linkg4 folders reinstalled and it all works perfectly, thanks very much now I can go sort out all my niggly problems!!
  2. Hi I've sent you my layout also I can seem to bring up run time values I have just a blank box when I click on them I'm trying to sort out an issue with the ac making the car lean when driving but every now and then I think it's the fan coming in but can't check without the run time tab I tried a uninstall and reinstall o latest software but still the same
  3. I have hopefully attached my table I use  (sorry for the late reply my r33 has been put away over winter and ive not been on here)  hope this helps ben and anyone else who needs it  Â
  4. hi since a few updates ago the pclink cannot load my last layout whenever I start pc link and it tries to load my map it states in a red pop up box 'XML document must have top level element' then below 'Line 0' if I then load my layout manually it loads up and works as it should but its very annoying and it also wont let me edit maps offline either all the maps just stay greyed out. What do I need to do to rectify this, my layout has quite a few pages and took me ages to do
  5. hi as above really i am not sure but it doesnt seem possible to use both at the same time as the cll tries to adjust the fueling when in overrun mode is it possible to somehow deactivate cll wideband mode when in overrun
  6. thanks scott i will give it a go this weekend
  7. hi scott ive sent the map through to you. Â Â thanks
  8. Hi since the latest software I can np longer use the closed loop lambda using the target afr table as the target for the closed loop adjustment I only get stoich and stoitch wideband is there no way to bring this back
  9. hi thanks scott have yo got an email i can send the map to
  10. hi ive been trying to follow these instructions for setting the cel to flash when indicating knock, but setting virtual aux to cel doesnt give you any switch settings nor does setting an aux output to cel give you any settings to play with what am i doing wrong here?  regards  lawrence  Hi Ryan, You can do this quite simply with the functionality that the G4 has. First you set a Virtual Auxiliary to CEL. Then you set the Auxiliary that runs your CEL to: SW Cond 1 : Aux Virtual Value (1 if you used Virtual Aux1) SW Cond 2: Knock > Value (What ever knock level you want it to trigger on). Switch Logic: Cond 1 or 2. This will mean your CEL will operate just as before, and also when knock goes over your set level. It will not store a fault code though. If you wanted to get really tricky, set a GP Output to Knock level, feed it back into a spare An Volt. When this goes to ground it will set off the CEL and store a fault code to the AnV you selected! Hope that helps. -Cameron
  11. Thanks scott I was hoping there would be a way!
  12. Hi I'm not sure if this is possible at the moment but it would be nice to be able to look at different tables at the same time I.e fuel and ignition or fuel and fuel overlay
  13. Firstly I assume an v6 is wired up to one of the lc1s output wires either the yellow or brown next you need to select lc1 from the wideband profiles if that is all done and it's still not working you need to open up the lc1 programmer (using the black little connector) and see what your voltages are for maximum and minimum afr you then need to create a profile for the wideband using one of the cal tables using these voltages and set an6 to read that cal table I had to muck around with it a bit as it was set up differently for the power fc I had on before but now works spot on
  14. Hi tried it tonight still the same 2nd through to 5th is fine but the number it produces in the runtime list is too great to input into the table for 1st
  15. hi im using 4.8.1.1033 with whatever firmware came with that i have idle timing etc  its only first i have an issue with the others work or will work when 1st is sorted out, i just cant input the number required
  16. im trying to setup gear detection 3 4 and 5 are ok and it detects it one but first comes up as 355 on the runtime list but the program only allows up to 200 2nd is around 180 and it won't recognise either of these due to 1st mucking anything up
  17. hi i know the coil pack dwell times for the rb26dett are 1.7 ms however the link uses a more complex table for dwell times, i was wondering if any tuners would be especially kind and send m,e the dwell times for the splitfires or do you just use the standard settings, at the mo i have 1.7 across the whole table which is obviously not correct but it runs fine, i would prefer it to be correct though also i still cant seem to start a new post without it showing n text please sort this forum out its the only one i use that does it!
  18. actually steve youve helped me out there i can run the knock using two tables instead of six as the rb26 only has two knock sensors which should free up a few tables  its still poor though that you cant use everything the ecu can do at once  thanks again
  19. but its crazy you cant run motorsport functions and have different boost levels or have multiple fuel maps its kind of pointless spending the money on an ecu that can do all this but at different times but not together i dont even want to use anti lag etc but just want my fueling to be correct and have 3 boost settings off 1 and 2 and it wont let me
  20. instead of starting my own wish list i also have this problem but have run out of tables on the link g4 xtreme i need to use 4d fuel but due to other tables active i cant use this table i would have thought a high end ecu such as this would have been able to use all the tables avaliable i dont even have motorsport functions enabled yet! off the top of my head i have dwell, iat correction, fuel1,fuel2, afr target, boost 1,2and 3, ignition1, then the tables for the a/c fan, idle etc
  21. hi i have setup my fueling so 3rd is 11.4 to 11.8 afr but if i log 1st gear pulls it registers as 13.4 2nd gear registers as 12.4 is this a problem? i understand that the engine is reving quicker and there is more load on the engine in 1st but the mgp stays roughly the same (within a few points) shall i run into the 10's in 3rd to richen up 1st or is there a better way if this is a problem?
  22. it seems to be when i use the quick text reply box i type it in and it doesnt put it on the forum
  23. it doesnt post up my text
  24. Thanks so much ross that is awesome my address is [email protected] I was just doing the mgp map as well I will switch back to tps to be honest it felt more responsive than mgp vs rpm One other thing though where do you take the map sensor reading from I've used the balance tube thing on the inlet the other end to the for take off it was used for factory boost Pressure sensor but I've binned this
  25. one more bit of advice is needed if you would be so kind! i assume the tps overlay is needed for different gears as you can hit the same mgp with different throttle positions due to being in the different gears, so my question is this which is the best gear to do it in? if i was to use third is it best to use very light throttle to get the smallest opening of the throttle as poss then use the tps overlay to correct up and down when using the other gears to be honest i found tps with mgp overlay easier to understand!
×
×
  • Create New...