shazad hanif

hi simon i have this plug n play board g3....that was upgraded to g4...i not seriously understanding the sofware of g4 compare to g3...can i go back to downgrade to g3 software? thanks shaz

Hi Friend of mine has 1jgte 2.5 ltr twin turbo mk3 supra swap in a rx7 was was wondering wat option of linkecu is availble for his set up? if wire in can link do a harrness conector that can conect to factory wiring harness thanks shaz

N which usb driver should i download for wrxlinkG3 (can to usb cable) Link ECU USB Drivers or ComLink USB Drivers thanks shaz

hey simon can the nos activation switch be conected through link?if so how shaz

hey ashley how is it goin do u sell knock block wiring harness seperately? wiring jack that goes to the (power,ground,knock senser)only with out the block itself?

hi i just recived the knock block with donut type senser 1)where shalli mount the senser on the motor? some say mount on top of the factory knock senser with a longer bolt going through both the senser and some use the spot adjecant to factory knock senser,looking for your advice 2)on the senser their are 2 pin clip left is for ground or right? tc shaz

hi i i recently got the dash display as i mentioned on the phone i conected dash display to the ecu it works fine but pclink didnt conect(online) when i tried it to connect both at the same time Therefore i took out the cable of dash display tried to connect pclink it got conected Cant pclink and dash display get conected at the same time? or only one will work at one time? shaz

hi knock controll of ej25 usdm with forge internals minee is set to gain chanel=x1 freq chanel=7.0 khz even when i put the ingnition to on position i get knock level of 8-9 when i do 100% throttle pull in third gear n shift in nutral even at throttle closed i i get knock level of 70-80 tried pulling the timing didnt help even in the free rev i get knock level of 40-70 ev pulling timing didnt help should i change freq channel 7.0khz ? my orignal block was ej20 now it ej25 wat shall i do as threshold is confusing me alot when i see knock count increasing shaz

hi we have set the knock threshold under boost 30s through out the knock table question is today i was boosting my car getting the knock count of 3 in boost so how does link pull timing?does it even pull time even if we get 1 knock count or does it pull timing after certian knock counts? in the real time value the knock count 3 mean car knocked 3 time or 3 knock counts mean does the previous knock counts add to current knock count to give the knock count of 3 help on this will be great thanks shaz

Is there any module in link products that can used for tuning G3 ecu funtions instead of having laptop in the car all the time Like there was hand held tuning module for G1 ecus shaz

hi Tried the ifone it i did not work with pclink dashlink of wrxlink board can be used for see runtime values and dataloging can dashlink be used for tuning as hand held tuning module or tuning can only be done with laptop with pclink software? thank you shaz

Thanks for the reply on that issue Can i use iphone instead of keeping laptop in the car all the time,can i just download link software on to that n conect to the supplied usb with link computer tune while im driving and also see digital run time,it will help checking knocks and other parameters of the car http://www.apple.com/iphone/ http://www.apple.com/iphone/questionsandanswers.html it has window xp thank you shaz

In link software of version 8-9 there is a widwow feul injector test and ingition spark test,cyclinder#1 #2 #3 #4 just want to know how is which cycliner is which in link software for Example cyclinder#1 is suppose to be RH,LH,FRONT,BACK? cyclinder#2 is suppose to be RH,LH,FRONT,BACK? cyclinder#3 is suppose to be RH,LH,FRONT,BACK? cyclinder#2 is suppose to be RH,LH,FRONT,BACK? realy wan to know this cuz we had to pull the 2.0 motor out of the car to swap 2.5 motor, started the new motor,pull the plugs out for compression test, compression test came perfect but the plugs RH showed car bieng rich and LH plugs showing lean i want to check fuel routing,injectors,spark first before doing anything else please can you let me know how does the fuel and ingition test works? and which cyclinder is which in wxrlink software ? thanks shaz

using wrxlink on 04 sti in my base map tthe knock thres table cells are set to 1000 and im getting knock level of 10 at all times where should i set cell value to from 1000 or should i leave all cells 1000 and wat level of knock i should'nt be bothered about as i have forged motor ej25 rod n piston with gt35r

n wat to do for the CLL for idle

I have wrxlink G3 pnp with xs conector and the inovate lc-1 with xd 16 display ,how shall i wire xs conector(with brown,green ,yellow wires on it) to wideband 02 and narraw band 02 to get to get readng on the pclink and what configrations i have to do in an volt2 options please explain in detail thank you shaz

can you let me know on this i have jdm 2.0 sti 2004(i guess ver 8 its called) i have the wrxlink G3 pnp(car started on option 2 jumpers) a week ago with a map senser and iat senser(as i want get rid of the maf) n im also planing to buy dash display linkin about months time as i will get use to wrxlink G3 for now i want to buy the defi dash display unit with oil pres,fuel pres,oil temp,water temp senser which are sold seperatly so question is if i just go for the sensers mentioned above and leave the defi display unit and buy the link dash display will i be able to wire it to wrxlink G3 PNP board and see data on link dash display

hi i recently got link map senser its got 3 wires white,green red i would like to know which is power,grond,sigal thanks