Jump to content

Flandrs

Members
  • Posts

    37
  • Joined

  • Last visited

Everything posted by Flandrs

  1. Flandrs

    Ac problems

    Tried that too without any luck.. i’ll have to measure to verify there is no wire issue between ecu and ac button..
  2. Flandrs

    Ac problems

    When pulling Connector out ac pump starts when looping connector with a little cable, ac turns off pull up is off when adjusting pressure high and low what is the recomended for that?
  3. Flandrs

    Ac problems

    So when pulling the connector out on the sensor, di 6 turns on and ac clutch activates but it won't happen anything when pushing ac button on the dash... Where should the ac button connect to the ecu??
  4. Flandrs

    Ac problems

    No that is what i also thought it should do but there is no sign of on and off when i set ac clutch to high di6 turns active all the time of i change back and tests low and high and with pull up there is still no reaction on di6
  5. Flandrs

    Ac problems

    Hi Have a evo viii here with some problems with the ac g4+ plug in first off i didn't got the pump to start then i changed ac clutch to high instead of low and the pump started.. injector 5/ac clutch Then ac is always on, if i turn of the button on the dashboard, ac is off. if i turn on heat, ac pump is on. Have checked runtime values to see if some turns on when pushing ac button on/off.. no luck... How can i solve this as it seems to be some wiring issues or setup that is wrong Couldn't attach tune here as it was to big..
  6. Flandrs

    Launch on and off

    Hi Was out testing this today and it seemed to work better, but it takes like forever to build boost.. It wasn't like that before (same engine hardware) is there something that you would like to change in my tune and maybe it will work better? could upload the last log as it was to big.. 0708-2.pclr launch logg.llg
  7. Flandrs

    Launch on and off

    haha sorry i'll try that then.. i looked in the help file and it was quoted there to 60..
  8. Flandrs

    Launch on and off

    so what would be good there? 60, 80?
  9. Flandrs

    Launch on and off

    Launchcontrol seems to go on and off and can't really understand why it does that? 1.llg 0629.pclr
  10. Hi Adam

     

    I was out and tested my car a bit, gearcut seems to work fine.

    I would be really glad if you could check my logg if you see anything that needs to be changed.

     

    Launchcontrol seems to go on and off and can't really understand why it does that?

    1.llg 0629.pclr

  11. Flandrs

    Boost time table

    Allright thank’s alot for that Adam !!
  12. Flandrs

    Boost time table

    Did you have any ideas Adam
  13. Flandrs

    Boost time table

    Checked my firmware and it was the latest, but updated anyway just to be sure. I changed all labels to english, easier to understand =) Gearcut upshift should be DI4 Downshift is not used Gearbox is dogbox PPG Race evo .pclr
  14. Flandrs

    Boost time table

    Allright i would like to ramp up the boost could you help me set it up? and gearcut Sterings, do you think it look ok?
  15. Flandrs

    Boost time table

    Hi Would it be possible to have a timer set to control boost? would like timer to start when launch goes to OFF and adjust boost to be a little lower first seconds, and then goes up to max boost. Or would it be easier to setup boost on gear? The feeling is that a timer would be more accurate than gear... Race evo .pclr
  16. Flandrs

    Overrun ign trim

    Thank you A bit confusing to adjust ignition under a fuel meny though..
  17. Flandrs

    Overrun ign trim

    Hi I'm not able to locate where this function is Overrun ign trim retards ignition -10 degrees... don't know where to adjust it.. I have dbw race evo Log 2020-03-24 8;23;30 pm.llg raceevo 20200324.pclr
  18. Thank's, i have it at 150hz now and it seems to work =)
  19. Wiring is Done and working i have a hella solid state relay so you think 100hz would be fine? The pump is a Davies and Craig Thanks for helping me out
  20. Hi I'm going to use a electric waterpump that i wan't to run with pwm control as i don't have any possibilties to have a thermostat. I have a Hella solid state relay and going to wire it 85 n/c 86 aux 7 pwm 30 + battery 87 + pump Now to the setup for the ECU, how should i set it up? What frequency and so on?? Anyone who could help me out with that? startad 2020.pclr
  21. Flandrs

    Gear indicator

    Hi is it possible to wire in a gearindicator display to the ecu and get it to work? i have link fury
  22. Hi i have a 2jz engine with belonging harness (oem) that is mounted into a mk4 n/a auto i cannot get any power to the ecu, i can get online though, i think power is going into the ecu somewhere else, i have no power on the red wire on connector A. this unit that is between oem ecu connector and vipec ecu, i measured and to get 12v+ to the red wire, it should get ignition on to pin 31 instead of pin 1 as it is now. What should i do to process, new engine harness or is this fixable? cheers Anders
  23. Flandrs

    output

    ok thank's for that. that will be very helpful for me.
  24. Flandrs

    output

    Hi Is it possible to turn on lights etc with aux output when i have activated launch and launching and when i reach 2bar i want a light to turn on. Is it possible? Or if oilpressue gets to low? Would also like to get a clean Fury map if it is possible
×
×
  • Create New...