Superstock22s
Members-
Posts
8 -
Joined
-
Last visited
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
Superstock22s's Achievements
Newbie (1/14)
0
Reputation
-
Hi all where is the best location to fit a IAT Sensor to Carb engine? Intake manifold below carb? Air filter Housing? Before anyone says why am i fitting it its purely to monitor wont be doing anything i just like to see numbers and with these Ecus i like the data i can see.
-
Hi Please have a read and if im wrong or anyone has a idea please share my question is ive used both my Temp pins for the ECT pin #15, IAT pin #16 sensors but want to run oil temp also. .I read somewhere i can use the AN Volt 2 pin#22 as a signal and a +5v pin#32 to run Oil temp sensor It also said i have to use a 1k ohm External Pull up Resistor in the +5v wire before the sensor does this sound correct? I'll list how i'm wiring bits up please share your thoughts as im green to this and its my first loom, i do have a loom already so will follow that for the ignition wasted spark setup just doesn't have all the other stuff wired into it. The Engine is a naturally Aspirated Toyota 1uz VVTI V8 running a 4BBL Holley Xp E85 Carburettor If someone has a wiring diagram of plug pinout to sensors would be great for future. ECT Sensor - #15 pin Temp 1 Yellow wire AND Green wire #24 pin Gnd Out. IAT Sensor - #16 pin Temp 2 Yellow Brown wire AND Green wire #24 pin Gnd Out. MTX-L Gauge Yellow 0-5v wire to #33 pin AN Volt 3 Yellow Black wire. OP Sensor - #17 pin AN Volt 1 Yellow /Blue wire AND #32 pin +5v Red/Blue wire AND #24 pin Gnd Out Green wire OT Sensor- #22 pin AN Volt 2 White/Brown wire AND #32 pin +5v Red/Blue Wire with a 1k ohm External pull up resistor? Or is there another way? Cheers Brent
-
These are the sensor I plan on using 3 pin oil pressure sensor So the wires to go with oil pressure are a +5v , green shield ground, signal wires ?
-
Ok Does this sound right Innovate MTX-L yellow wire goes to pin 17/An Volt 1 for the wideband? It has no Brown wire. Oil Pressure yellow/black wire to pin 33 /An Volt 3? Oil Temperature yellow/brown wire to pin 16/Temp 2? And a green sensor ground wire pin 7/Sheild/Ground to each of the oil temp and pressure switches? Water temp one was already wired into temp 1 and a green wire. Let me know if this looks right. Do i then need to go into ecu and turn these things on or do they come on automatically?
-
Can someone show me the wires and colours and where everything goes trying to wire in MTX-L gauge but have no clue where to start. Im a beginner running only Ignition as engine is carbed but want to monitor Water temp,Oil pressure, oil temp and wideband. Cheers
-
Sorry should have mentioned no injection running 4bbl Carburetor so only output Rpm correct? That was the only wire from loom and a power wire when i got it to install. It also had the water temp one but i havent hooked that up yet didnt fit my sensor.
-
OK Thanks for that but my loom has the wires removed for the items i want to now log. The Atom plug header pin out which wires do i need to reinstall for oil pressure,oil temp,water temp ,and hook up MTX-L gauge? Sorry for dumbness again all new to me. Brent
-
Superstock22s reacted to a post in a topic: Innovate MTX-L wideband to link G4+Atom
-
Superstock22s reacted to a post in a topic: Innovate MTX-L wideband to link G4+Atom
-
Ok bear with me I’m a beginner to this. Can I hook up this gauge to the datalogging of the link if so how and what do I require? some Help please cheers Brent