Pointz

Update. I have my aem working on an analogue input now. And I have racetech connected via canbus, I have no faults at all now. My issue is it is not displaying anything other than rpm. I would like to display, boost, coolant temp and lambda. Can anyone explain how to do this or a link to a guide please. Thanks

Well thats great if I knew that I wouldn't of bothered with the rt dash, its already cost best part of £800 and now I know it won't even work without even more work. Definitely not going to recommend it. I have a serial to usb adapter here if thats what I need? Could I connect my aem via another input? An v ? Would it work as well as being on the canbus

Right update! I took the can wires back to ecu re-twisted them neater (they were quite loose) heatshrank the wires to keep them in place, now have no faults. Have reconnected the aem and no faults (fuelling is correct again now aswell) As soon as I receive the correct resistors I will fit that then try get the dash working. (Not looking forward to that) And I can set it to dash2 pro and it'll work OK being a dash 2 (not pro)

Just tested resistance on can h and can l between the 2 and I have 122ohms and 119.8 with probes reversed. This is without the resistor . Yes I bought the link interface from rt and followed the above wiring diagram. I will get the resistor fitted then report back! Will I have to configure all the outputs that I want displayed in pclink? Only would like coolant temp, boost and rpm

Yes I bought the link interface from rt and followed the above wiring diagram. I will get the resistor fitted then report back! Will I have to configure all the outputs that I want displayed in pclink? Only would like coolant temp, boost and rpm

Yes that was with just the rt dash2 All other channels set to off and aem disconnected. I am going to redo all of the can wiring from ecu to devices. And add a resistor. The can wiring is less than 1m but if I have 2 devices running off it then I should have it?

Yes it does, the window i had open there was streams rather than mode. When connecting the devices I should be loading a stream to there as per the help file instructions?

Yes I have just powered down both and have 3 errors now Error passive Bus warning Receive error counter 127

Disconnected from the bus but about to go power it down now!

I have set up can channel to just the rt dash and have the following errors Stuff error Form error Acknowledge error Bit recessive error Crc error Error passive Bus warning Receive error counter 127 And with both channels set to off. Stuff error Form error Crc error Error Passive Bus warning

I'm going to do more on it later today, spoke to my tuner as my tune has gone off and he said the can errors can cause things to go open loop therefore affect the tune. So I quickly disconnected the dash as I had the aem working fine prior to dash install. Will update shortly thanks for your time Adam

With dash channel off it clears some codes, this is just with wideband connected

Yes I have the aem as well Unplug as in kill the power to the aem? I have both aem and rt dash on the can h can l wires from the atom

ca18det racetech.pclr Please see attached pclr Thanks

Yes il do it as soon as I'm home thanks

Long overdue update on this. I have the dash all connected up using the linkecu - rt dash interface. It is wired to the can h / can l wires from the link loom but I seem to be having a few faults on the can. Form error stuff error Bus warning error Bit recessive error Receive error counter And the dash doesn't seem to be receiving data from the ecu. I have set it up as id1000, 20hz, etc as per guide. I'd like to send rpm, coolant temp and boost pressure from ecu to dash. Is it necessary to use a canser lead? Has anyone successfully setup an rt dash 2? That would be happy to help out. Thanks

Thanks Adam I will contact racetech and see if they can supply me one

I have been reading multiple threads but not having much luck, I have purchase a racetech dash 2 and would like to connect this to my link atom via can. What I cant figure out is what wire/connector i need to purchase in order to connect the 2 together! Any help is greatly appreciated and apologies if this has been covered previously.

All sorted it would appear i didn't apply all settings when setting up can. Thanks adam

I will get out and get the file shortly, its a link g4 atom, wire in on my ca18det. Using the can H (orange/green) and can L (orange/yellow) from the link a loom.

I have followed the setup instructions as per pclink help section but looking at the runtime values I have some faults. Anyone shed some light on where I've gone wrong.

My ca with a link plugin would occasionally pop but not fire, the ecu plug was a bit dicky. Could be worth checking also can you do ign and inj test on the monsoon so you know all are firing!

Any other input? Anything that should of been setup that hasn't?

It's meant to be a finished tune