Jump to content

Search the Community

Showing results for tags 'help'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Link
    • G4+
    • G4x
  • General Topics
    • Guest
    • WishList
    • Engine Tuning
    • Customers Vehicles
  • Vi-PEC
    • Vi-PEC i Series
    • ViPEC V Series
    • ViPEC Power Sport
  • Historic Products
    • Link G4
    • Link G2 G3
    • Link G1


There are no results to display.


  • Bryan
  • 카지노 사이트, 카지노 추천«TSG79.COM
  • 2JZ Tuning Tips
  • Arjun haniz
  • Slot Joker Gaming
  • SV388 Live
  • IDNPLAY Judi Poker Online

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







ECU model

Serial Number

Found 9 results

  1. I have absolutely no tune on my 4age except for the startup map my wiring harness guy did. He told me to get an AFR gauge so I did. It's a AEM X gauge and it causing me some issues. My wiring harness has a wbo2 input with a white and brown wire but when connected to my sensor gauge it gets no input in the ecu. I'm running a monsoonX btw. The gauge reads 25 afr at idle but my idle doesnt work at all. Any help would be appreciated as the engine is brand new rebuilt.
  2. Hi! I recently bought a built lancer evo 3 with a Link G4 pnp ecu. I discovered an issue where I assume the ecu power cuts on wot. I'm assuming its something in the stock harness but I haven't gone through it yet so i might be wrong. Now this issue doesn't show up until the car has been running for a few minutes. The car works just fine for about ~10 minutes after starting the engine, and it also works fine after restarting the car mid run. I'm new to this but i managed to log some data and I had a friend ride with me while it was happening and it's not showing any fault codes so I have no idea where to start to be honest. As I mentioned earlier it probably has something to do with the stock harness being 20 years old but you never know. The engine is good for about 500hp and it runs great when it wants to. Has someone ever encountered this before? Ill attatch the tune and the log where the power cut or whatever it is happens. starts at ~6:20 min into the log https://www.dropbox.com/sh/9k9ga1ejm1ifhr6/AADC93Cv3KZ_wVIGa_qwjSL8a?dl=0 <-tune and logs Specs: CP pistons Eagle rods Bc valve springs BC 272 cam Fic injectors 1200cc New oil pump and water pump Athena headgasket Arp bolts Aeromotive fpr Tial 44mm wg Jrm dump (woosh) Acl bearings Garett 3076bbr
  3. Hello Thank you for your attention. I need help with my Subaru WRX STI 2011 JDM EJ207. I have implemented my Link G4+ fury with my car. But my engine does not increase rpm more than 5500rpm. Under 5000 rpm works fine. I've tried changing my ignition timing from 45 BTDC to 0 BTDC but it does not have any effects. I've also double checked my dwell table, Ignition delay, Ignition charge time as same as shown in help in PCLink that it's same as the EJ20 quad AVCS configuration. Do you have any guesses? Thank you very much.
  4. Hello, want to start this by saying sorry if I posted this in the wrong area, its my first time writing a post. So I have a 3sge beams from an altezza in my '86 300zx Z31, ive followed multiple upon multiple pin outs/ instructions and Im still having a no start issue. I believe I have everything right, but I could very well not. Any information anyone is willing to share im very thankful for! Its almost been a year since I started this swap and I just want to drive my car again.
  5. driftma

    1jz vvti tune

    I'm hopeful if some one could have a quick look at this tune and see does it actually look like it should, it was tuned by a tuner but the figures for inlet vvti control don't seem to add up with links help file to what they should be doing. The car also has very poor throttle response, from reving it up from idle. any help on the correct vvti table settings that I need would be very helpful, the car is fitted with hks 264 cams if that makes any difference and also if the rest of the setup looks correct. File attached below. first run on sunoco e20-R.pclr
  6. Hi guys, chasing a base map /start up map for my link g4+ extreme running it on a 1jzgte vvti. 1000cc injectors Stock ingition and ignitor No dbw or ethrottle. 264/272cams To4z turbo Stock everything else
  7. HELP PLEASE!!! I have a Aem UGO Wideband that is currently setup on ANVolt 4 it is currently working but it reading only Lambda. I have all my settings to read AFR on both metric and Imperial but it still Reads Lambda/sensor Volt in my logs I have the Gauge setup per instructions and still no luck. Any help would be Great Thanks, Devin
  8. rb ali

    base maps

    hey, so I'm wondering and new to this (my 1st time with Linky) where do I get base maps ,do i just download . really want to make sure it starts before I get to dyno.. Need one for rb30det
  9. Do you have a problem with setting up your ECU? Posting on the forum is a great way to get a solution. If you want a quick solution to your problem then we need a good description of the problem, your current base-map, and a PCLog of the problem occurring. Watch the following video to learn how to do this. Need some technical help?
  • Create New...