MRE32 Posted July 20, 2020 Report Share Posted July 20, 2020 Gidday folks I have just installed some R35 coils in my RB26 (R32 GTR) - previously standard. I have a single table of recommended dwell times for the coils. (as below) Recommended dwell settings: 5.0ms @ 8v 4.8ms @ 9v 4.7ms @ 10v 4.6ms @ 11v 4.4ms @ 12v 4.2ms @ 13v 4.1ms @ 14v 4.0ms @ 15v 3.8ms @ 16v when I went to look at the table (because I'm a noob) I expected to see a single column to adjust these settings but was met with a table with multiple columns. I don't plan on going into the tuners for another month but would to get this fixed up as I am a little paranoid I'll burn them out as I have seen mentioned thanks in advance for your help!! Quote Link to comment Share on other sites More sharing options...
dx4picco Posted July 20, 2020 Report Share Posted July 20, 2020 I believe you have as column axis RPM. and line axis voltage, do you? in that case you can put the values you have in each column. Or modify your table axis to get your expected format. Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 20, 2020 Report Share Posted July 20, 2020 If you want just a 2D table then right click on the table, choose axis setup, then (click the green wave next to engine speed) change the X axis parameter to none. Quote Link to comment Share on other sites More sharing options...
MRE32 Posted July 22, 2020 Author Report Share Posted July 22, 2020 Quote Link to comment Share on other sites More sharing options...
MRE32 Posted July 22, 2020 Author Report Share Posted July 22, 2020 Quote Link to comment Share on other sites More sharing options...
MRE32 Posted July 22, 2020 Author Report Share Posted July 22, 2020 Thanks gents I think I got it now *fingers crossed* Quote Link to comment Share on other sites More sharing options...
S13Sky Posted September 11, 2022 Report Share Posted September 11, 2022 On 7/22/2020 at 12:11 AM, MRE32 said: How did you get this view? I’ve been playing around with the software for hours trying to get this Quote Link to comment Share on other sites More sharing options...
Adamw Posted September 11, 2022 Report Share Posted September 11, 2022 6 hours ago, S13Sky said: How did you get this view? I’ve been playing around with the software for hours trying to get this What specific view are you talking about? In that pic there is a standard table in text mode and runtimes value list view. Quote Link to comment Share on other sites More sharing options...
S13Sky Posted September 13, 2022 Report Share Posted September 13, 2022 sorry disregard we got it sorted out Quote Link to comment Share on other sites More sharing options...
RonSanDiego Posted December 13, 2022 Report Share Posted December 13, 2022 On 7/22/2020 at 3:11 AM, MRE32 said: How did you get to this screen. Im only able to see dwell time configuration with the rpm included. Im trying to install r35 coilpacks. Quote Link to comment Share on other sites More sharing options...
Adamw Posted December 13, 2022 Report Share Posted December 13, 2022 Right mouse click on table>axis setup, set the Y axis to none. RonSanDiego 1 Quote Link to comment Share on other sites More sharing options...
RonSanDiego Posted December 15, 2022 Report Share Posted December 15, 2022 Im a noob at this, i figured out how to get to that screen. My question now is I plug the usb to my laptop with just the acc on the ignition and change what i need to do on the dwell time (r35 coil packs). After doing so how do i save the new dwell time and make sure its in the G4X. Quote Link to comment Share on other sites More sharing options...
Adamw Posted December 15, 2022 Report Share Posted December 15, 2022 Make your changes when you are online (ecu powered up), any changes you make will turn blue. To make any changes permanent you need to do a "store" before switching off ignition. To do a store hit the F4 key (or ctrl+S), you should see any of the blue settings change to white when stored. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.